Hi, On 12/24/05, iwant4x4jeep <[EMAIL PROTECTED]> wrote: > I'm upgrade my FreeBSD5.4 system to 6.0-STABLE. Now ACPI suspend-to-ram > (sleepstate #3) don't work ( before upgrade all works fine) > > Processor - Pentium 4 2.4Ghz > Mother Board - ASUS P4PE > > # dmesg | grep -i acpi > ACPI APIC Table: <ASUS P4PE > > > Features=0xbfebfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,C > MOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE> > acpi0: <ASUS P4PE> on motherboard > acpi0: Overriding SCI Interrupt from IRQ 9 to IRQ 22 > acpi0: Power Button (fixed) > pci_link0: <ACPI PCI Link LNKA> irq 5 on acpi0 > pci_link1: <ACPI PCI Link LNKB> irq 9 on acpi0 > pci_link2: <ACPI PCI Link LNKC> irq 9 on acpi0 > pci_link3: <ACPI PCI Link LNKD> irq 9 on acpi0 > pci_link4: <ACPI PCI Link LNKE> irq 10 on acpi0 > pci_link5: <ACPI PCI Link LNKF> on acpi0 > pci_link6: <ACPI PCI Link LNKG> on acpi0 > pci_link7: <ACPI PCI Link LNKH> irq 11 on acpi0 > Timecounter "ACPI-fast" frequency 3579545 Hz quality 1000 > acpi_timer0: <24-bit timer at 3.579545MHz> port 0xe408-0xe40b on acpi0 > cpu0: <ACPI CPU> on acpi0 > acpi_throttle0: <ACPI CPU Throttling> on cpu0 > acpi_button0: <Power Button> on acpi0 > pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0 > pci0: <ACPI PCI bus> on pcib0 > pcib1: <ACPI PCI-PCI bridge> at device 1.0 on pci0 > pci1: <ACPI PCI bus> on pcib1 > pcib2: <ACPI PCI-PCI bridge> at device 30.0 on pci0 > pci2: <ACPI PCI bus> on pcib2 > fdc0: <floppy drive controller> port 0x3f2-0x3f5,0x3f7 irq 6 drq 2 on acpi0 > ppc0: <ECP parallel printer port> port 0x378-0x37f,0x778-0x77b irq 7 drq 3 on > ac > pi0 > sio0: <16550A-compatible COM port> port 0x3f8-0x3ff irq 4 flags 0x10 on acpi0 > sio1: <16550A-compatible COM port> port 0x2f8-0x2ff irq 3 on acpi0 > atkbdc0: <Keyboard controller (i8042)> port 0x60,0x64 irq 1 on acpi0 > > When I (as usually before) enter in console 'acpiconf -s 3' (Really I use > sudo, so type 'sudo acpiconf -s 3', computer suspends, but don't resume after > power on. > > I have problem with hi-ressolution modes in console ( Using pathes from > DragonFlyBSD project, which is allready included with freebsd since 6.0). > I'm enabled VESA and SC_PIXEL_MODE options in kernel, when I enter > 'vidcontrol -i mode' - all modes(what i need) displays, but if I use > vidcontrol MODE_279 (for example), monitor enter 1024x768 mode, but I can't > see anything. > First time I think that I do something wrong (Don't load needed fonts for > example), but when I try it on another computer- I can't believe my eyes.. > It was real 1024x768 in FreeBSD Console !!!
Are you sure that your configuration cacn support MODE_279? Will other modes work? Cheers, -- Xin LI <[EMAIL PROTECTED]> http://www.delphij.net
_______________________________________________ [email protected] mailing list http://lists.freebsd.org/mailman/listinfo/freebsd-stable To unsubscribe, send any mail to "[EMAIL PROTECTED]"
