--On Tuesday, February 26, 2008 16:58:45 +1030 Daniel O'Connor
<[EMAIL PROTECTED]> wrote:
On Tue, 26 Feb 2008, Jeremy Chadwick wrote:
> Doesn't make much sense to me. I'm not very familiar with how the
> usb system works, so I'm not sure where to look to find the
> problem. There's no /dev/umass either.
For umass devices to work, you need to have uhci (or ohci if your
system uses that USB bus type), ehci (for USB2.0), usb (obvious), and
umass. The kicker is that you also need scbus, da, and possibly pass.
They must be in the kernel otherwise it wouldn't have linked.
Does the device appear in usbdevs -v when it's connected?
Does anything show up in dmesg?
# uname -a
FreeBSD utd65257.utdallas.edu 7.0-RELEASE FreeBSD 7.0-RELEASE #2: Tue Feb 26
09:07:31 CST 2008 [EMAIL PROTECTED]:/usr/obj/usr/src/sys/GENERIC
i386
I recompiled the kernel this morning, and the symptoms have changed. (I
noticed some recent commits to cvs.) Now, if I have my Maxtor hard drive
attached to the system during boot, the system hangs and I get umass errors.
umass0: BBB reset failed, TIMEOUT
umass0: BBB bulk-in clear stall failed, TIMEOUT
umass0: BBB bulk-out clear stall failed, TIMEOUT
These continue until the system reboots. If I disconnect (physically) the
drive, the system boots normally and *then* I can attach the drive and mount it.
# usbdevs -v
Controller /dev/usb0:
addr 1: full speed, self powered, config 1, UHCI root hub(0x0000),
Intel(0x0000), rev 1.00
port 1 powered
port 2 powered
Controller /dev/usb1:
addr 1: full speed, self powered, config 1, UHCI root hub(0x0000),
Intel(0x0000), rev 1.00
port 1 powered
port 2 powered
Controller /dev/usb2:
addr 1: high speed, self powered, config 1, EHCI root hub(0x0000),
Intel(0x0000), rev 1.00
port 1 addr 5: high speed, self powered, config 1, Maxtor 3200(0x3200), Maxtor
Corporation(0x0d49), rev 0.01
port 2 addr 2: high speed, self powered, config 1, product 0x2504(0x2504),
vendor 0x0424(0x0424), rev 0.01
port 1 addr 3: low speed, power 100 mA, config 1, USB Optical Mouse(0x4d15),
vendor 0x0461(0x0461), rev 2.00
port 2 addr 4: low speed, power 100 mA, config 1, Microsoft Natural Keyboard
Elite(0x000b), vendor 0x045e(0x045e), rev 2.07
port 3 powered
port 4 powered
port 3 powered
port 4 powered
port 5 powered
port 6 powered
Controller /dev/usb3:
addr 1: full speed, self powered, config 1, UHCI root hub(0x0000),
Intel(0x0000), rev 1.00
port 1 powered
port 2 powered
Controller /dev/usb4:
addr 1: full speed, self powered, config 1, UHCI root hub(0x0000),
Intel(0x0000), rev 1.00
port 1 powered
port 2 powered
Controller /dev/usb5:
addr 1: full speed, self powered, config 1, UHCI root hub(0x0000),
Intel(0x0000), rev 1.00
port 1 powered
port 2 powered
Controller /dev/usb6:
addr 1: high speed, self powered, config 1, EHCI root hub(0x0000),
Intel(0x0000), rev 1.00
port 1 powered
port 2 powered
port 3 powered
port 4 powered
port 5 powered
port 6 powered
--
Paul Schmehl ([EMAIL PROTECTED])
Senior Information Security Analyst
The University of Texas at Dallas
http://www.utdallas.edu/ir/security/
_______________________________________________
[email protected] mailing list
http://lists.freebsd.org/mailman/listinfo/freebsd-stable
To unsubscribe, send any mail to "[EMAIL PROTECTED]"
