On 24/ago/09, at 02:47, Mike Tancsa wrote:
At 08:05 AM 8/23/2009, Gianni wrote:
I've seen a few posts related to the Huawei E169 3G modem which have
reported this device as working under 7.2. I have the u3g driver
loaded but the modem is only recognised as umass, I tried disabling
umass and the device came up as ugen.
My 7.2-STABLE is newly built today, log messages below, should this
modem work out of the box or is there some extra configuration
needed?
Any suggestion much appreciated.
Make sure umass is loaded as well as the u3g driver. Then, after
all has booted up, try
usbdevs -v
camcontrol eject pass0
usbdevs
Some devices need that to put them into 'modem mode'... If it works,
you should see /dev/cuaU0.0 and you should see a differences in the
output of usbdevs before and after the camcontrol eject pass0
---Mike
Thanks Mike, unfortunately that did not work, the /dev/cuaU0.0 device
did not appear.
-Gianni
nicknack# usbdevs -v
Controller /dev/usb0:
addr 1: full speed, self powered, config 1, UHCI root hub(0x0000),
Intel(0x0000), rev 1.00
port 1 powered
port 2 powered
Controller /dev/usb1:
addr 1: full speed, self powered, config 1, UHCI root hub(0x0000),
Intel(0x0000), rev 1.00
port 1 powered
port 2 powered
Controller /dev/usb2:
addr 1: full speed, self powered, config 1, UHCI root hub(0x0000),
Intel(0x0000), rev 1.00
port 1 powered
port 2 powered
Controller /dev/usb3:
addr 1: full speed, self powered, config 1, UHCI root hub(0x0000),
Intel(0x0000), rev 1.00
port 1 powered
port 2 powered
Controller /dev/usb4:
addr 1: high speed, self powered, config 1, EHCI root hub(0x0000),
Intel(0x0000), rev 1.00
port 1 powered
port 2 addr 3: high speed, self powered, config 1, HUAWEI
Mobile(0x1446), HUAWEI Technology(0x12d1), rev 0.00
port 3 powered
port 4 powered
port 5 powered
port 6 addr 2: high speed, power 500 mA, config 1, USB2.0-
CRW(0x0158), Generic(0x0bda), rev 58.87
port 7 powered
port 8 powered
nicknack# camcontrol eject pass0
Unit stopped successfully, Media ejected
nicknack# usbdevs -v
Controller /dev/usb0:
addr 1: full speed, self powered, config 1, UHCI root hub(0x0000),
Intel(0x0000), rev 1.00
port 1 powered
port 2 powered
Controller /dev/usb1:
addr 1: full speed, self powered, config 1, UHCI root hub(0x0000),
Intel(0x0000), rev 1.00
port 1 powered
port 2 powered
Controller /dev/usb2:
addr 1: full speed, self powered, config 1, UHCI root hub(0x0000),
Intel(0x0000), rev 1.00
port 1 powered
port 2 powered
Controller /dev/usb3:
addr 1: full speed, self powered, config 1, UHCI root hub(0x0000),
Intel(0x0000), rev 1.00
port 1 powered
port 2 powered
Controller /dev/usb4:
addr 1: high speed, self powered, config 1, EHCI root hub(0x0000),
Intel(0x0000), rev 1.00
port 1 powered
port 2 addr 3: high speed, self powered, config 1, HUAWEI
Mobile(0x1446), HUAWEI Technology(0x12d1), rev 0.00
port 3 powered
port 4 powered
port 5 powered
port 6 addr 2: high speed, power 500 mA, config 1, USB2.0-
CRW(0x0158), Generic(0x0bda), rev 58.87
port 7 powered
port 8 powered
_______________________________________________
[email protected] mailing list
http://lists.freebsd.org/mailman/listinfo/freebsd-usb
To unsubscribe, send any mail to "[email protected]"
