Hi,
I can't use my external HDD attached to my laptop. The drive enclosure is a Fantec db 229 U3 case (USB3). My laptop has only USB2 ports. I have tested this with both FreeBSD 9.0 RELEASE and FreeBSD 9 STABLE - same issues. Tested with linux too on the same hardware and it is working fine. The manual which came with the drive enclosure states Linux, Mac OSX and Windows support. Can someone please point me to the right direction? I have included some dumps bellow. Many thanks, Peter dmesg: usb_alloc_device: set address 2 failed (USB_ERR_STALLED, ignored) usbd_setup_device_desc: getting device descriptor at addr 2 failed, USB_ERR_STALLED usbd_req_re_enumerate: addr=2, set address failed! (USB_ERR_STALLED, ignored) usbd_setup_device_desc: getting device descriptor at addr 2 failed, USB_ERR_STALLED usbd_req_re_enumerate: addr=2, set address failed! (USB_ERR_STALLED, ignored) usbd_setup_device_desc: getting device descriptor at addr 2 failed, USB_ERR_STALLED ugen1.2: at usbus1 (disconnected) uhub_reattach_port: could not allocate new device usbconfig output: ugen0.1: at usbus0, cfg=0 md=HOST spd=FULL (12Mbps) pwr=SAVE ugen1.1: at usbus1, cfg=0 md=HOST spd=FULL (12Mbps) pwr=SAVE ugen2.1: at usbus2, cfg=0 md=HOST spd=HIGH (480Mbps) pwr=SAVE ugen3.1: at usbus3, cfg=0 md=HOST spd=FULL (12Mbps) pwr=SAVE ugen4.1: at usbus4, cfg=0 md=HOST spd=FULL (12Mbps) pwr=SAVE ugen5.1: at usbus5, cfg=0 md=HOST spd=FULL (12Mbps) pwr=SAVE ugen6.1: at usbus6, cfg=0 md=HOST spd=HIGH (480Mbps) pwr=SAVE ugen0.2: at usbus0, cfg=0 md=HOST spd=FULL (12Mbps) pwr=ON ugen0.3: at usbus0, cfg=0 md=HOST spd=FULL (12Mbps) pwr=ON ugen4.2: at usbus4, cfg=0 md=HOST spd=FULL (12Mbps) pwr=ON pciconf: uhci2@pci0:0:29:0:class=0x0c0300 card=0x20aa17aa chip=0x28308086 rev=0x03 hdr=0x00 vendor = 'Intel Corporation' device = '82801H (ICH8 Family) USB UHCI Controller' class = serial bus subclass = USB bar [20] = type I/O Port, range 32, base 0x18a0, size 32, enabled uhci3@pci0:0:29:1:class=0x0c0300 card=0x20aa17aa chip=0x28318086 rev=0x03 hdr=0x00 vendor = 'Intel Corporation' device = '82801H (ICH8 Family) USB UHCI Controller' class = serial bus subclass = USB bar [20] = type I/O Port, range 32, base 0x18c0, size 32, enabled uhci4@pci0:0:29:2:class=0x0c0300 card=0x20aa17aa chip=0x28328086 rev=0x03 hdr=0x00 vendor = 'Intel Corporation' device = '82801H (ICH8 Family) USB UHCI Controller' class = serial bus subclass = USB bar [20] = type I/O Port, range 32, base 0x18e0, size 32, enabled ehci1@pci0:0:29:7:class=0x0c0320 card=0x20ab17aa chip=0x28368086 rev=0x03 hdr=0x00 vendor = 'Intel Corporation' device = '82801H (ICH8 Family) USB2 EHCI Controller' class = serial bus subclass = USB bar [10] = type Memory, range 32, base 0xfe227000, size 1024, enabled cap 01[50] = powerspec 2 supports D0 D3 current D0 cap 0a[58] = EHCI Debug Port at offset 0xa0 in map 0x14 _______________________________________________ freebsd-usb@freebsd.org mailing list http://lists.freebsd.org/mailman/listinfo/freebsd-usb To unsubscribe, send any mail to "freebsd-usb-unsubscr...@freebsd.org"