On 07/05/14 20:28, Tur-Wei Chan wrote:
Hi,

On 1/7/2014 12:17 AM, Tur-Wei Chan wrote:
Hi,
On 30/6/2014 1:02 AM, Hans Petter Selasky wrote:
On 06/29/14 16:41, Tur-Wei Chan wrote:
Hi,

Got a Zotac ID91 mini-PC
(http://www.zotac.com/products/mini-pcs/zbox/product/zbox/detail/zbox-id91-1.html)

recently and installed FreeBSD (10-STABLE, r267719) on it.

Hooking up my Mediasonic ProRaid HUR3-SU3S3 to the USB3 ports however
showed the drives up at only USB2.0 speeds:


Hi,

What does "pciconf -lv" say?

I see you have a Lynx Point USB 3.0. They are a bit troublesome. Have
you played with the port routing mask under hw.usb.xhci ?

--HPS


pciconf -lv said (as attached previously):

xhci0@pci0:0:20:0:      class=0x0c0330 card=0xb20619da chip=0x8c318086
rev=0x05 hdr=0x00
    vendor     = 'Intel Corporation'
    device     = 'Lynx Point USB xHCI Host Controller'
    class      = serial bus
    subclass   = USB



I got the disks to attach at USB3.0:

Jul  6 02:00:41 z2 kernel: xhci0: <Intel Lynx Point USB 3.0 controller>
mem 0xf7d00000-0xf7d0ffff irq 16 at
Jul  6 02:00:41 z2 kernel: xhci0: 32 byte context size.
Jul  6 02:00:41 z2 kernel: xhci0: Port routing mask set to 0x00000003
Jul  6 02:00:41 z2 kernel: usbus0 on xhci0
...
Jul  6 02:00:41 z2 kernel: uhub0: <Intel EHCI root HUB, class 9/0, rev
2.00/1.00, addr 1> on usbus1
Jul  6 02:00:41 z2 kernel: ugen0.1: <0x8086> at usbus0
...
Jul  6 02:02:15 z2 kernel: da0 at umass-sim0 bus 0 scbus2 target 0 lun 0
Jul  6 02:02:15 z2 kernel: da0: <JMicron Disk0 0104> Fixed Direct Access
SCSI-6 device
Jul  6 02:02:15 z2 kernel: da0: Serial Number 00000000000000000000
Jul  6 02:02:15 z2 kernel: da0: 400.000MB/s transfers
Jul  6 02:02:15 z2 kernel: da0: 1907729MB (3907029168 512 byte sectors:
255H 63S/T 243201C)
Jul  6 02:02:15 z2 kernel: da0: quirks=0x2<NO_6_BYTE>
Jul  6 02:02:15 z2 kernel: da1 at umass-sim0 bus 0 scbus2 target 0 lun 1
Jul  6 02:02:15 z2 kernel: da1: <JMicron Disk1 0104> Fixed Direct Access
SCSI-6 device
Jul  6 02:02:15 z2 kernel: da1: Serial Number 00000000000000000000
Jul  6 02:02:15 z2 kernel: da1: 400.000MB/s transfers
Jul  6 02:02:15 z2 kernel: da1: 1907729MB (3907029168 512 byte sectors:
255H 63S/T 243201C)
Jul  6 02:02:15 z2 kernel: da1: quirks=0x2<NO_6_BYTE>

usbconfig list:
ugen1.1: <EHCI root HUB Intel> at usbus1, cfg=0 md=HOST spd=HIGH
(480Mbps) pwr=SAVE (0mA)
ugen0.1: <XHCI root HUB 0x8086> at usbus0, cfg=0 md=HOST spd=SUPER
(5.0Gbps) pwr=SAVE (0mA)
ugen2.1: <EHCI root HUB Intel> at usbus2, cfg=0 md=HOST spd=HIGH
(480Mbps) pwr=SAVE (0mA)
ugen1.2: <product 0x8008 vendor 0x8087> at usbus1, cfg=0 md=HOST
spd=HIGH (480Mbps) pwr=SAVE (0mA)
ugen2.2: <product 0x8000 vendor 0x8087> at usbus2, cfg=0 md=HOST
spd=HIGH (480Mbps) pwr=SAVE (0mA)
ugen1.3: <USB2.0-CRW Generic> at usbus1, cfg=0 md=HOST spd=HIGH
(480Mbps) pwr=ON (500mA)
ugen2.3: <USB Receiver Logitech> at usbus2, cfg=0 md=HOST spd=FULL
(12Mbps) pwr=ON (98mA)
ugen0.2: <JMS56x Series JMicron> at usbus0, cfg=0 md=HOST spd=SUPER
(5.0Gbps) pwr=ON (2mA)

What I did:
a) Set hw.usb.xhci.xhci_port_route="0x3" in /boot/loader.conf
b) Fixed /sys/dev/usb/controller/xhci.c as follows:

     --- dev/usb/controller/xhci.c   (revision 268290)
     +++ dev/usb/controller/xhci.c   (working copy)
     @@ -567,7 +567,7 @@
             if (sc->sc_port_route != NULL) {
                     /* Route all ports to the XHCI by default */
                     sc->sc_port_route(sc->sc_bus.parent,
     -                   ~xhciroute, xhciroute);
     +                   xhciroute, ~xhciroute);
             }
             return (0);
      }


Hi,

Thank you for input. Does:

hw.usb.xhci.xhci_port_route="0xFFFFFFFC"

work for you instead of fixing xhci.c ?

--HPS


Previously when I set the port route mask to -1, the xhci init would
fail.  It seems for my H81 board that only ports 1 and 2 are available
for USB 3.0 [1] so only the value 0x03 for the port route would work for
me.


Regards

   -T.W.Chan-

[1] From the document "IntelĀ® 8 Series/C220 Series Chipset Family
Platform Controller Hub(PCH)"

Is this information available in the PCI address space?

--HPS

_______________________________________________
freebsd-usb@freebsd.org mailing list
http://lists.freebsd.org/mailman/listinfo/freebsd-usb
To unsubscribe, send any mail to "freebsd-usb-unsubscr...@freebsd.org"

Reply via email to