しのだと申します。

平野さん、こんにちわ。

In message "[FreeBSD-users-jp 88195] Re: USB  デバイス動作報告  HDH-SUE250",
Akihiro HIRANO wrote...
 > USB 1.1だと思います。
 >
 >FreeBSD 5.4-RELEASE-p4
 >
 >usb4: EHCI version 1.0
 >usb4: companion controllers, 2 ports each: usb0 usb1 usb2 usb3
 >usb4: <EHCI (generic) USB 2.0 controller> on ehci0
 >usb4: USB revision 2.0
 >uhub4: Intel EHCI root hub, class 9/0, rev 2.00/1.00, addr 1
 >uhub4: 8 ports with 8 removable, self powered

ハっと思って dmesg.boot を見てみますと、確かに USB I/F は、

%cat /var/run/dmesg.boot|grep usb
usb0: <UHCI (generic) USB controller> on uhci0
usb0: USB revision 1.0
usb1: <UHCI (generic) USB controller> on uhci1
usb1: USB revision 1.0
usb2: <UHCI (generic) USB controller> on uhci2
usb2: USB revision 1.0

と、USB 1.0 として認識されているようです。

DELL PowerEdge 830 なので、実際には USB 2.0 なのですが・・・

ということで、PowerEdge 830 の USB I/F を 2.0 で認識させられな
いか情報を探していますが、まだ見つかっていません。
(PowerEdge 830 のコントローラは「EHCI インタフェースを使った 
USB 2.0 コントローラ」ではないということなのでしょうか? USB 
のこともよくわかってないのでとんちんかんで済みません)

ご存じの方がいらっしゃれば、ご教示いただければ幸いです。

↓こんなマシンです。

%cat /var/run/dmesg.boot
Copyright (c) 1992-2005 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
        The Regents of the University of California. All rights reserved.
FreeBSD 4.11-RELEASE #0: Fri Jan 21 17:21:22 GMT 2005
    [EMAIL PROTECTED]:/usr/obj/usr/src/sys/GENERIC
Timecounter "i8254"  frequency 1193182 Hz
CPU: Intel(R) Pentium(R) D CPU 3.00GHz (3000.12-MHz 686-class CPU)
  Origin = "GenuineIntel"  Id = 0xf44  Stepping = 4
  Features=0xbfebfbff
<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH
,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE>
  Hyperthreading: 2 logical CPUs
real memory  = 1073479680 (1048320K bytes)
avail memory = 1039384576 (1015024K bytes)
Preloaded elf kernel "kernel" at 0xc055c000.
Warning: Pentium 4 CPU: PSE disabled
Pentium Pro MTRR support enabled
md0: Malloc disk
Using $PIR table, 11 entries at 0xc00fb900
npx0: <math processor> on motherboard
npx0: INT 16 interface
pcib0: <Host to PCI bridge> on motherboard
pci0: <PCI bus> on pcib0
pcib1: <PCI to PCI bridge (vendor=8086 device=2779)> irq 0 at device 1.0 on pci0
pci1: <PCI bus> on pcib1
pcib2: <PCI to PCI bridge (vendor=8086 device=27d0)> irq 0 at device 28.0 on 
pci0
pci2: <PCI bus> on pcib2
pcib3: <PCI to PCI bridge (vendor=8086 device=032c)> at device 0.0 on pci2
pci3: <PCI bus> on pcib3
aac0: <Dell CERC SATA RAID 2> mem 0xf8000000-0xfbffffff irq 3 at device 1.0 on 
pci3
aac0: Unknown processor 100MHz, 48MB cache memory, optional battery not 
installed
aac0: Kernel 4.1-0, Build 7417, S/N 4e1b55
aac0: Supported 
Options=1097c<WCACHE,DATA64,HOSTTIME,RAID50,WINDOW4GB,SOFTERR,ALARM>
pcib4: <PCI to PCI bridge (vendor=8086 device=27e0)> irq 0 at device 28.4 on 
pci0
pci4: <PCI bus> on pcib4
bge0: <Broadcom BCM5721 Gigabit Ethernet, ASIC rev. 0x4101> mem 
0xfe7f0000-0xfe7fffff irq 3 at 
device 0.0 on pci4
bge0: Ethernet address: XX:XX:XX:XX:XX:XX
miibus0: <MII bus> on bge0
brgphy0: <BCM5750 10/100/1000baseTX PHY> on miibus0
brgphy0:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseTX, 
1000baseTX-FDX, auto
pcib5: <PCI to PCI bridge (vendor=8086 device=27e2)> irq 0 at device 28.5 on 
pci0
pci5: <PCI bus> on pcib5
uhci0: <UHCI (generic) USB controller> port 0xcce0-0xccff irq 11 at device 29.0 
on pci0
usb0: <UHCI (generic) USB controller> on uhci0
usb0: USB revision 1.0
uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
uhci1: <UHCI (generic) USB controller> port 0xccc0-0xccdf irq 10 at device 29.1 
on pci0
usb1: <UHCI (generic) USB controller> on uhci1
usb1: USB revision 1.0
uhub1: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub1: 2 ports with 2 removable, self powered
uhci2: <UHCI (generic) USB controller> port 0xcca0-0xccbf irq 5 at device 29.2 
on pci0
usb2: <UHCI (generic) USB controller> on uhci2
usb2: USB revision 1.0
uhub2: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub2: 2 ports with 2 removable, self powered
pci0: <USB controller> at 29.7 irq 11
pcib6: <Intel 82801BA/BAM (ICH2) Hub to PCI bridge> at device 30.0 on pci0
pci6: <PCI bus> on pcib6
pci6: <VGA-compatible display device> at 5.0
isab0: <PCI to ISA bridge (vendor=8086 device=27b8)> at device 31.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <Generic PCI ATA controller> port 
0xfc00-0xfc0f,0-0x3,0-0x7,0-0x3,0-0x7 irq 0 at device 
31.1 on pci0
ata0: at 0x1f0 irq 14 on atapci0
ata1: at 0x170 irq 15 on atapci0
pci0: <unknown card> (vendor=0x8086, dev=0x27da) at 31.3 irq 0
orm0: <Option ROMs> at iomem 
0xc0000-0xc7fff,0xc8000-0xc8fff,0xca800-0xce7ff,0xec000-0xeffff on 
isa0
pmtimer0 on isa0
fdc0: <NEC 72065B or clone> at port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on isa0
fdc0: FIFO enabled, 8 bytes threshold
fd0: <1440-KB 3.5" drive> on fdc0 drive 0
atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0
atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0
kbd0 at atkbd0
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
sio0: type 16550A
sio1: configured irq 3 not in bitmap of probed irqs 0
ppc0: parallel port not found.
acd0: CDROM <LITE-ON CD-ROM LTN-489S> at ata0-master PIO4
aacd0: <RAID 1 (Mirror)> on aac0
aacd0: 238385MB (488213504 sectors)
Mounting root from ufs:/dev/aacd0s1a

----
SHINODA Masanori <[EMAIL PROTECTED]> 
Net & Field Co.,Ltd. Internet Service Section 
Phone 082-239-0350  Fax(IP) 050-5517-9651 
Portable... 090-6419-9919 

メールによる返信