お世話になります。
   Option "Log" "sync"
でやってみました。
うまくいきました。
マニュアルを読んで教えていただきありがとうございます。

Logを以下に示します。
ほとんどうまくいってます。
最後に
(--) S3VIRGE(0): videoram:  4096k
がエラーの原因のようです。
Xorg7.2か7.3(おそらく今インストールしようとしているのは7.4でしょうか)の時
は
Depth  24
で作動していたのですが,・・・・・・・・。
ここでとまるというのはハードが原因でしょうか?
増設メモリは乗せていないので,おそらくメモリは2Mだと思います。


X.Org X Server 1.6.0
Release Date: 2009-2-25
X Protocol Version 11, Revision 0
Build Operating System: FreeBSD 7.2-PRERELEASE i386
Current Operating System: FreeBSD myhost.my.domain 7.2-RELEASE FreeBSD
7.2-RELEASE #0: Fri May  1 08:49:13 UTC 2009
r...@walker.cse.buffalo.edu:/usr/obj/usr/src/sys/GENERIC i386
Build Date: 22 April 2009  02:40:51PM

 Before reporting problems, check http://wiki.x.org
 to make sure that you have the latest version.
Markers: (--) probed, (**) from config file, (==) default setting,
 (++) from command line, (!!) notice, (II) informational,
 (WW) warning, (EE) error, (NI) not implemented, (??) unknown.
(==) Log file: "/var/log/Xorg.0.log", Time: Sun Nov  8 07:20:01 2009
(==) Using config file: "/etc/X11/xorg.conf"
(==) ServerLayout "X.org Configured"
(**) |-->Screen "Screen0" (0)
(**) |   |-->Monitor "Monitor0"
(**) |   |-->Device "Card0"
(**) |-->Input Device "Mouse0"
(**) |-->Input Device "Keyboard0"
(**) Option "Log" "sync"
(==) Automatically adding devices
(==) Automatically enabling devices
(**) Syncing logfile enabled
(**) FontPath set to:
 /usr/local/lib/X11/fonts/misc/,
 /usr/local/lib/X11/fonts/TTF/,
 /usr/local/lib/X11/fonts/OTF,
 /usr/local/lib/X11/fonts/Type1/,
 /usr/local/lib/X11/fonts/100dpi/,
 /usr/local/lib/X11/fonts/75dpi/,
 /usr/local/lib/X11/fonts/misc/,
 /usr/local/lib/X11/fonts/TTF/,
 /usr/local/lib/X11/fonts/OTF,
 /usr/local/lib/X11/fonts/Type1/,
 /usr/local/lib/X11/fonts/100dpi/,
 /usr/local/lib/X11/fonts/75dpi/,
 built-ins
(**) ModulePath set to "/usr/local/lib/xorg/modules"
(WW) AllowEmptyInput is on, devices using drivers 'kbd', 'mouse' or
'vmmouse' will be disabled.
(WW) Disabling Mouse0
(WW) Disabling Keyboard0
(II) Loader magic: 0x6a0
(II) Module ABI versions:
 X.Org ANSI C Emulation: 0.4
 X.Org Video Driver: 5.0
 X.Org XInput driver : 4.0
 X.Org Server Extension : 2.0
(II) Loader running on freebsd
(--) Using syscons driver with X support (version 2.0)
(--) using VT number 9

(--) PCI:*(0...@0:9:0) S3 Inc. ViRGE/DX or /GX rev 1, Mem @
0xdc000000/67108864, BIOS @ 0x????????/65536
(II) System resource ranges:
 [0] -1 0 0x000f0000 - 0x000fffff (0x10000) MX[B]
 [1] -1 0 0x000c0000 - 0x000effff (0x30000) MX[B]
 [2] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX[B]
 [3] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[B]
 [4] -1 0 0x00000000 - 0x000000ff (0x100) IX[B]
(II) "extmod" will be loaded. This was enabled by default and also specified
in the config file.
(II) "dbe" will be loaded. This was enabled by default and also specified in
the config file.
(II) "glx" will be loaded. This was enabled by default and also specified in
the config file.
(II) "record" will be loaded. This was enabled by default and also specified
in the config file.
(II) "dri" will be loaded. This was enabled by default and also specified in
the config file.
(II) "dri2" will be loaded. This was enabled by default and also specified
in the config file.
(II) LoadModule: "dbe"
(II) Loading /usr/local/lib/xorg/modules/extensions//libdbe.so
(II) Module dbe: vendor="X.Org Foundation"
 compiled for 1.6.0, module version = 1.0.0
 Module class: X.Org Server Extension
 ABI class: X.Org Server Extension, version 2.0
(II) Loading extension DOUBLE-BUFFER
(II) LoadModule: "dri"
(II) Loading /usr/local/lib/xorg/modules/extensions//libdri.so
(II) Module dri: vendor="X.Org Foundation"
 compiled for 1.6.0, module version = 1.0.0
 ABI class: X.Org Server Extension, version 2.0
(II) Loading extension XFree86-DRI
(II) LoadModule: "dri2"
(II) Loading /usr/local/lib/xorg/modules/extensions//libdri2.so
(II) Module dri2: vendor="X.Org Foundation"
 compiled for 1.6.0, module version = 1.0.0
 ABI class: X.Org Server Extension, version 2.0
(II) Loading extension DRI2
(II) LoadModule: "extmod"
(II) Loading /usr/local/lib/xorg/modules/extensions//libextmod.so
(II) Module extmod: vendor="X.Org Foundation"
 compiled for 1.6.0, module version = 1.0.0
 Module class: X.Org Server Extension
 ABI class: X.Org Server Extension, version 2.0
(II) Loading extension MIT-SCREEN-SAVER
(II) Loading extension XFree86-VidModeExtension
(II) Loading extension XFree86-DGA
(II) Loading extension DPMS
(II) Loading extension XVideo
(II) Loading extension XVideo-MotionCompensation
(II) Loading extension X-Resource
(II) LoadModule: "glx"
(II) Loading /usr/local/lib/xorg/modules/extensions//libglx.so
(II) Module glx: vendor="X.Org Foundation"
 compiled for 1.6.0, module version = 1.0.0
 ABI class: X.Org Server Extension, version 2.0
(==) AIGLX disabled
(II) Loading extension GLX
(II) LoadModule: "record"
(II) Loading /usr/local/lib/xorg/modules/extensions//librecord.so
(II) Module record: vendor="X.Org Foundation"
 compiled for 1.6.0, module version = 1.13.0
 Module class: X.Org Server Extension
 ABI class: X.Org Server Extension, version 2.0
(II) Loading extension RECORD
(II) LoadModule: "s3virge"
(II) Loading /usr/local/lib/xorg/modules/drivers//s3virge_drv.so
(II) Module s3virge: vendor="X.Org Foundation"
 compiled for 1.6.0, module version = 1.10.2
 Module class: X.Org Video Driver
 ABI class: X.Org Video Driver, version 5.0
(II) S3VIRGE: driver (version 1.10.2) for S3 ViRGE chipsets: virge, 86C325,
 virge vx, 86C988, virge dx, virge gx, 86C375, 86C385, virge gx2,
 86C357, virge mx, 86C260, virge mx+, 86C280, trio 3d, 86C365,
 trio 3d/2x, 86C362, 86C368
(II) Primary Device is: PCI 0...@00:09:0
(WW) Falling back to old probe method for s3virge
(--) Chipset virge dx found
(II) resource ranges after xf86ClaimFixedResources() call:
 [0] -1 0 0x000f0000 - 0x000fffff (0x10000) MX[B]
 [1] -1 0 0x000c0000 - 0x000effff (0x30000) MX[B]
 [2] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX[B]
 [3] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[B]
 [4] -1 0 0x00000000 - 0x000000ff (0x100) IX[B]
(II) resource ranges after probing:
 [0] -1 0 0x000f0000 - 0x000fffff (0x10000) MX[B]
 [1] -1 0 0x000c0000 - 0x000effff (0x30000) MX[B]
 [2] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX[B]
 [3] 0 0 0x000a0000 - 0x000affff (0x10000) MS[B]
 [4] 0 0 0x000b0000 - 0x000b7fff (0x8000) MS[B]
 [5] 0 0 0x000b8000 - 0x000bffff (0x8000) MS[B]
 [6] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[B]
 [7] -1 0 0x00000000 - 0x000000ff (0x100) IX[B]
 [8] 0 0 0x000003b0 - 0x000003bb (0xc) IS[B]
 [9] 0 0 0x000003c0 - 0x000003df (0x20) IS[B]
(II) Loading sub module "vgahw"
(II) LoadModule: "vgahw"
(II) Loading /usr/local/lib/xorg/modules//libvgahw.so
(II) Module vgahw: vendor="X.Org Foundation"
 compiled for 1.6.0, module version = 0.1.0
 ABI class: X.Org Video Driver, version 5.0
(==) S3VIRGE(0): Depth 24, (--) framebuffer bpp 24
(==) S3VIRGE(0): RGB weight 888
(==) S3VIRGE(0): Default visual is TrueColor
(==) S3VIRGE(0): Using HW Cursor
(==) S3VIRGE(0): mx_cr3a_fix.
(II) Loading sub module "vbe"
(II) LoadModule: "vbe"
(II) Loading /usr/local/lib/xorg/modules//libvbe.so
(II) Module vbe: vendor="X.Org Foundation"
 compiled for 1.6.0, module version = 1.1.0
 ABI class: X.Org Video Driver, version 5.0
(II) Loading sub module "int10"
(II) LoadModule: "int10"
(II) Loading /usr/local/lib/xorg/modules//libint10.so
(II) Module int10: vendor="X.Org Foundation"
 compiled for 1.6.0, module version = 1.0.0
 ABI class: X.Org Video Driver, version 5.0
(II) S3VIRGE(0): initializing int10
(==) S3VIRGE(0): Write-combining range (0xa0000,0x20000) was already clear
(==) S3VIRGE(0): Write-combining range (0xc0000,0x40000) was already clear
(II) S3VIRGE(0): Primary V_BIOS segment is: 0xc000
(==) S3VIRGE(0): Write-combining range (0x0,0x1000) was already clear
(II) S3VIRGE(0): VESA BIOS detected
(II) S3VIRGE(0): VESA VBE Version 2.0
(II) S3VIRGE(0): VESA VBE Total Mem: 4096 kB
(II) S3VIRGE(0): VESA VBE OEM: S3 Incorporated. ViRGE /DX /GX
(II) S3VIRGE(0): VESA VBE OEM Software Rev: 1.1
(II) S3VIRGE(0): VESA VBE OEM Vendor: S3 Incorporated.
(II) S3VIRGE(0): VESA VBE OEM Product: ViRGE /DX /GX
(II) S3VIRGE(0): VESA VBE OEM Product Rev: Rev B
(--) S3VIRGE(0): Chipset: "virge dx"
(==) S3VIRGE(0): XVideo supported.
(II) S3VIRGE(0): vgaHWGetIOBase: hwp->IOBase is 0x03d0, hwp->PIOOffset is
0x0000
(II) S3VIRGE(0): vgaHWGetIOBase: hwp->IOBase is 0x03d0, hwp->PIOOffset is
0x0000
(==) S3VIRGE(0): Write-combining range (0xa0000,0x10000) was already clear
(II) Loading sub module "ddc"
(II) LoadModule: "ddc"
(II) Module "ddc" already built-in
(II) Loading sub module "ddc"
(II) LoadModule: "ddc"
(II) Module "ddc" already built-in
(II) S3VIRGE(0): VESA VBE DDC supported
(II) S3VIRGE(0): VESA VBE DDC Level 2
(II) S3VIRGE(0): VESA VBE DDC transfer in appr. 1 sec.
(II) S3VIRGE(0): VESA VBE DDC read successfully
(II) S3VIRGE(0): Manufacturer: MEL  Model: 4742  Serial#: 16843009
(II) S3VIRGE(0): Year: 2006  Week: 19
(II) S3VIRGE(0): EDID Version: 1.3
(II) S3VIRGE(0): Analog Display Input,  Input Voltage Level: 0.700/0.300 V
(II) S3VIRGE(0): Sync:  Separate
(II) S3VIRGE(0): Max Image Size [cm]: horiz.: 34  vert.: 27
(II) S3VIRGE(0): Gamma: 2.20
(II) S3VIRGE(0): DPMS capabilities: StandBy Suspend Off; RGB/Color Display
(II) S3VIRGE(0): Default color space is primary color space
(II) S3VIRGE(0): First detailed timing is preferred mode
(II) S3VIRGE(0): GTF timings supported
(II) S3VIRGE(0): redX: 0.640 redY: 0.340   greenX: 0.290 greenY: 0.610
(II) S3VIRGE(0): blueX: 0.140 blueY: 0.070   whiteX: 0.313 whiteY: 0.329
(II) S3VIRGE(0): Supported VESA Video Modes:
(II) S3VIRGE(0): 720x...@70hz
(II) S3VIRGE(0): 640x...@60hz
(II) S3VIRGE(0): 640x...@67hz
(II) S3VIRGE(0): 640x...@72hz
(II) S3VIRGE(0): 640x...@75hz
(II) S3VIRGE(0): 800x...@56hz
(II) S3VIRGE(0): 800x...@60hz
(II) S3VIRGE(0): 800x...@72hz
(II) S3VIRGE(0): 800x...@75hz
(II) S3VIRGE(0): 832x...@75hz
(II) S3VIRGE(0): 1024x...@60hz
(II) S3VIRGE(0): 1024x...@70hz
(II) S3VIRGE(0): 1024x...@75hz
(II) S3VIRGE(0): 1280x1...@75hz
(II) S3VIRGE(0): 1152x...@75hz
(II) S3VIRGE(0): Manufacturer's mask: 0
(II) S3VIRGE(0): Supported Future Video Modes:
(II) S3VIRGE(0): #0: hsize: 1280  vsize 960  refresh: 60  vid: 16513
(II) S3VIRGE(0): #1: hsize: 1280  vsize 1024  refresh: 60  vid: 32897
(II) S3VIRGE(0): #2: hsize: 1280  vsize 1024  refresh: 66  vid: 34433
(II) S3VIRGE(0): #3: hsize: 1280  vsize 1024  refresh: 76  vid: 36993
(II) S3VIRGE(0): #4: hsize: 1024  vsize 768  refresh: 66  vid: 18017
(II) S3VIRGE(0): #5: hsize: 1152  vsize 864  refresh: 70  vid: 19057
(II) S3VIRGE(0): #6: hsize: 1280  vsize 960  refresh: 75  vid: 20353
(II) S3VIRGE(0): #7: hsize: 1280  vsize 1024  refresh: 75  vid: 36737
(II) S3VIRGE(0): Supported additional Video Mode:
(II) S3VIRGE(0): clock: 108.0 MHz   Image Size:  338 x 270 mm
(II) S3VIRGE(0): h_active: 1280  h_sync: 1328  h_sync_end 1440 h_blank_end
1688 h_border: 0
(II) S3VIRGE(0): v_active: 1024  v_sync: 1025  v_sync_end 1028 v_blanking:
1066 v_border: 0
(II) S3VIRGE(0): Ranges: V min: 55 V max: 76 Hz, H min: 31 H max: 81 kHz,
PixClock max 130 MHz
(II) S3VIRGE(0): Monitor name: RDT176LM
(II) S3VIRGE(0): Serial No: 65213279AJ
(II) S3VIRGE(0): EDID (in hex):
(II) S3VIRGE(0):  00ffffffffffff0034ac424701010101
(II) S3VIRGE(0):  1310010308221b78efc5c5a3574a9c23
(II) S3VIRGE(0):  125054bfef8081408180818681906146
(II) S3VIRGE(0):  714a814f818f302a009851002a403070
(II) S3VIRGE(0):  1300520e1100001e000000fd00374c1f
(II) S3VIRGE(0):  510d000a202020202020000000fc0052
(II) S3VIRGE(0):  44543137364c4d0a20202020000000ff
(II) S3VIRGE(0):  003635323133323739414a0a20200065
(II) S3VIRGE(0): EDID vendor "MEL", prod id 18242
(II) S3VIRGE(0): Using hsync ranges from config file
(II) S3VIRGE(0): Using vrefresh ranges from config file
(II) S3VIRGE(0): Printing DDC gathered Modelines:
(II) S3VIRGE(0): Modeline "1280x1024"x0.0  108.00  1280 1328 1440 1688  1024
1025 1028 1066 +hsync +vsync (64.0 kHz)
(II) S3VIRGE(0): Modeline "800x600"x0.0   40.00  800 840 968 1056  600 601
605 628 +hsync +vsync (37.9 kHz)
(II) S3VIRGE(0): Modeline "800x600"x0.0   36.00  800 824 896 1024  600 601
603 625 +hsync +vsync (35.2 kHz)
(II) S3VIRGE(0): Modeline "640x480"x0.0   31.50  640 656 720 840  480 481
484 500 -hsync -vsync (37.5 kHz)
(II) S3VIRGE(0): Modeline "640x480"x0.0   31.50  640 664 704 832  480 489
492 520 -hsync -vsync (37.9 kHz)
(II) S3VIRGE(0): Modeline "640x480"x0.0   30.24  640 704 768 864  480 483
486 525 -hsync -vsync (35.0 kHz)
(II) S3VIRGE(0): Modeline "640x480"x0.0   25.18  640 656 752 800  480 490
492 525 -hsync -vsync (31.5 kHz)
(II) S3VIRGE(0): Modeline "720x400"x0.0   28.32  720 738 846 900  400 412
414 449 -hsync +vsync (31.5 kHz)
(II) S3VIRGE(0): Modeline "1280x1024"x0.0  135.00  1280 1296 1440 1688  1024
1025 1028 1066 +hsync +vsync (80.0 kHz)
(II) S3VIRGE(0): Modeline "1024x768"x0.0   78.75  1024 1040 1136 1312  768
769 772 800 +hsync +vsync (60.0 kHz)
(II) S3VIRGE(0): Modeline "1024x768"x0.0   75.00  1024 1048 1184 1328  768
771 777 806 -hsync -vsync (56.5 kHz)
(II) S3VIRGE(0): Modeline "1024x768"x0.0   65.00  1024 1048 1184 1344  768
771 777 806 -hsync -vsync (48.4 kHz)
(II) S3VIRGE(0): Modeline "832x624"x0.0   57.28  832 864 928 1152  624 625
628 667 -hsync -vsync (49.7 kHz)
(II) S3VIRGE(0): Modeline "800x600"x0.0   49.50  800 816 896 1056  600 601
604 625 +hsync +vsync (46.9 kHz)
(II) S3VIRGE(0): Modeline "800x600"x0.0   50.00  800 856 976 1040  600 637
643 666 +hsync +vsync (48.1 kHz)
(II) S3VIRGE(0): Modeline "1152x864"x0.0  108.00  1152 1216 1344 1600  864
865 868 900 +hsync +vsync (67.5 kHz)
(II) S3VIRGE(0): Modeline "1280x960"x0.0  108.00  1280 1376 1488 1800  960
961 964 1000 +hsync +vsync (60.0 kHz)
(II) S3VIRGE(0): Modeline "1280x1024"x0.0  108.00  1280 1328 1440 1688  1024
1025 1028 1066 +hsync +vsync (64.0 kHz)
(II) S3VIRGE(0): Modeline "1280x1024"x66.0  121.35  1280 1368 1504 1728
1024 1025 1028 1064 -hsync +vsync (70.2 kHz)
(II) S3VIRGE(0): Modeline "1280x1024"x76.0  141.82  1280 1376 1512 1744
1024 1025 1028 1070 -hsync +vsync (81.3 kHz)
(II) S3VIRGE(0): Modeline "1024x768"x66.0   71.63  1024 1080 1192 1360  768
769 772 798 -hsync +vsync (52.7 kHz)
(II) S3VIRGE(0): Modeline "1152x864"x70.0   96.77  1152 1224 1344 1536  864
865 868 900 -hsync +vsync (63.0 kHz)
(II) S3VIRGE(0): Modeline "1280x960"x75.0  129.86  1280 1368 1504 1728  960
961 964 1002 -hsync +vsync (75.2 kHz)
(II) S3VIRGE(0): Modeline "1280x1024"x0.0  135.00  1280 1296 1440 1688  1024
1025 1028 1066 +hsync +vsync (80.0 kHz)
(==) S3VIRGE(0): Write-combining range (0x0,0x1000) was already clear
(==) S3VIRGE(0): Using gamma correction (1.0, 1.0, 1.0)
(--) S3VIRGE(0): videoram:  4096k

Fatal server error:
Caught signal 11.  Server aborting


Please consult the The X.Org Foundation support
  at http://wiki.x.org
 for help.
Please also check the log file at "/var/log/Xorg.0.log" for additional
information.


----- Original Message ----- 
From: "Satoshi Kimura" <satosi.kim...@nifty.com>
To: <FreeBSD-users-jp@jp.FreeBSD.org>
Sent: Sunday, November 08, 2009 1:43 AM
Subject: [FreeBSD-users-jp 92582] Re: Trobles of Xwindows on FreeBSD 7.2


> こんにちは,木村です.
>
> Taku さん : [FreeBSD-users-jp 92580][d.o 92581]
>
> > logの時間は更
> > 新されているので,空っぽのlogが残っている状態です。
>
> > (4)ブラックアウトするとキーを受け付けなくなるの
> > で,resetして再起動しています。
>   log が残らないのは,これが原因だと思います.
>
>   私自身はこれを使ったことがないので,紹介するのは無責任かも
> しれませんが,xorg.conf にこんな Option があります.
> /var/log/Xorg.0.log が残る可能性が上がると思います.
>
> % man xorg.conf
> SERVERFLAGS SECTION
>        Option "Log" "string"
>               This option controls whether the log is flushed and/or
synced to
>               disk after each message.  Possible values  are  flush  or
sync.
>               Unset by default.
>
> 本当は,flush と sync と両方やりたいところですが,
>
>    Option "Log" "flush"
>    Option "Log" "sync"
>
> こう併記したら,前者だけしか効きませんでした.
>
> /var/log/Xorg.0.log           : (**) Option "Log" "flush"
> % startx -- -verbose 1 >& log : (**) Flushing logfile enabled
>
> 先ず
>    Option "Log" "sync"
> の方で試していただけますか.
>
> -----------------------------------------------------------
> > % startx -- -verbose 1 >& log
> > では,logが出てきませんでした。
>
> log という名前のファイルのサイズが 0 ということですか?
>
> /var/log/Xorg.0.log は Xserver (/usr/local/bin/Xorg) の出力で
> あるのに対し,これは (当然) startx で実行されるものすべて,
> すなわち .xinitrc で実行する内容の出力も含んでいます.なので,
>
> .xinitrc で
>
> (こことか)
> xterm &
> (こことかに)
> exec twm
>
> 具体的にどれだけとは分かりませんが,大量の文字を strerr に出力
> するプログラムや sync を挟んだら log が残る可能性が増すかも.
>
>   まず,先述の二つの Option を試して下さい.それでダメなら,
> このやり方をうちで実験してみます.(さすがに reset するつもりは
> ありませんが.)
>
>                       Satoshi Kimura  (satosi.kim...@nifty.com)
>

メールによる返信