Hi Neel,
I updated my STABLE to r281384M and applied the patch. It seems that the patch solved the issue: # pciconf -vl | grep ppt ppt0@pci0:0:20:0: class=0x0c0330 card=0x8c311849 chip=0x8c318086 rev=0x05 hdr=0x00 ppt1@pci0:0:26:0: class=0x0c0320 card=0x8c2d1849 chip=0x8c2d8086 rev=0x05 hdr=0x00 ppt2@pci0:1:0:0: class=0x010601 card=0x91721849 chip=0x91721b4b rev=0x11 hdr=0x00 As I'm not a developer, please tell me whether this patch will be added to STABLE or if I need to patch again when I update the system in the future. Thank you very much, Luis 2015-04-10 6:30 GMT+01:00 Neel Natu <[email protected]>: > Hi Luis, > > This following patch should do the trick: > https://people.freebsd.org/~neel/patches/usb_pci_probe_default.patch > > The patch is against -current although it applies cleanly to 10-stable as > well. > > best > Neel > > On Thu, Apr 9, 2015 at 3:32 PM, Luis P. Mendes <[email protected]> wrote: >> Hi, >> >> 2015-04-09 22:25 GMT+01:00 Neel Natu <[email protected]>: >>> Hi Luis, >>> >>> On Thu, Apr 9, 2015 at 1:43 PM, Luis P. Mendes <[email protected]> wrote: >>>> Hi, >>>> >>>> I'm trying to passthrough a USB host controller (2.0 or 3.0) but there >>>> seems to be some kind of problem. >>>> >>>> # uname -a >>>> FreeBSD leao 10.1-STABLE FreeBSD 10.1-STABLE #0 r279201: Mon Feb 23 >>>> 18:55:46 UTC 2015 >>>> [email protected]:/usr/obj/usr/src/sys/GENERIC amd64 >>>> >>>> VT-d is enabled in bios. >>>> CPU is a Intel Xeon E3-1246v3 Haswell >>>> >>>> >>>> # cat /boot/loader.conf >>>> # load radeon firmware not presented >>>> pptdevs="0/26/0 1/0/0 0/20/0" >>>> blackhole_load="YES" >>>> >>>> # pciconf -lv >>>> # only relevant >>>> ehci0@pci0:0:26:0: class=0x0c0320 card=0x8c2d1849 chip=0x8c2d8086 >>>> rev=0x05 hdr=0x00 >>>> vendor = 'Intel Corporation' >>>> device = 'Lynx Point USB Enhanced Host Controller' >>>> class = serial bus >>>> subclass = USB >>>> >>>> xhci0@pci0:0:20:0: class=0x0c0330 card=0x8c311849 chip=0x8c318086 >>>> rev=0x05 hdr=0x00 >>>> vendor = 'Intel Corporation' >>>> device = 'Lynx Point USB xHCI Host Controller' >>>> class = serial bus >>>> subclass = USB >>>> >>>> ppt0@pci0:1:0:0: class=0x010601 card=0x91721849 chip=0x91721b4b >>>> rev=0x11 hdr=0x00 >>>> >>>> >>>> Only the 1:0:0 disk controler is hidden. The two USB controllers, one >>>> ehci and one xhci are not. >>>> >>>> Why don't the controllers get hidden? >>>> Is the blackhole_load="YES" still relevant? I tried with and without >>>> that line to no avail. >>>> Is my STABLE version too old? >>>> >>> >>> The blackhole driver is not needed anymore since that functionality >>> was moved into vmm.ko. >>> >>> Can you replace the line blackhole_load="YES" to vmm_load="YES" in >>> loader.conf? >> >> The vmm_load="YES" line was already present. >> The full contents of the file are: >> >> % cat /boot/loader.conf >> net.fibs=4 >> >> radeonkmsfw_CAICOS_pfp_load="YES" >> radeonkmsfw_CAICOS_me_load="YES" >> radeonkmsfw_BTC_rlc_load="YES" >> radeonkmsfw_CAICOS_mc_load="YES" >> radeonkms_load="YES" >> >> vmm_load="YES" >> nmdm_load="YES" >> if_bridge_load="YES" >> if_tap_load="YES" >> >> pptdevs="1/0/0 0/20/0 0/26/0" >> >> >> >> Thanks, >> >> >> Luis _______________________________________________ [email protected] mailing list http://lists.freebsd.org/mailman/listinfo/freebsd-virtualization To unsubscribe, send any mail to "[email protected]"
