On 12/09/2016 12:21, Grzegorz Junka wrote:
I am following the official guide:
https://www.freebsd.org/doc/handbook/virtualization-host-bhyve.html
After installing Centos6 and starting the guest there is no network
inside the VM:
[root@localhost ~]# ping 8.8.8.8
connect: Network is unreachable
[root@localhost ~]# ifconfig
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:65536 Metric:1
RX packets:4 errors:0 dropped:0 overruns:0 frame:0
TX packets:4 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:260 (260.0 b) TX bytes:260 (260.0 b)
On the host:
root@ultrabook:~ # ifconfig
ath0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> metric 0 mtu
2290
ether 74:2f:68:cb:d6:2a
nd6 options=21<PERFORMNUD,AUTO_LINKLOCAL>
media: IEEE 802.11 Wireless Ethernet autoselect mode 11ng
status: associated
lo0: flags=8049<UP,LOOPBACK,RUNNING,MULTICAST> metric 0 mtu 16384
options=600003<RXCSUM,TXCSUM,RXCSUM_IPV6,TXCSUM_IPV6>
inet6 ::1 prefixlen 128
inet6 fe80::1%lo0 prefixlen 64 scopeid 0x2
inet 127.0.0.1 netmask 0xff000000
nd6 options=21<PERFORMNUD,AUTO_LINKLOCAL>
bridge0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> metric 0
mtu 1500
ether 02:6c:a7:69:c7:00
nd6 options=9<PERFORMNUD,IFDISABLED>
id 00:00:00:00:00:00 priority 32768 hellotime 2 fwddelay 15
maxage 20 holdcnt 6 proto rstp maxaddr 2000 timeout 1200
root id 00:00:00:00:00:00 priority 32768 ifcost 0 port 0
member: tap0 flags=143<LEARNING,DISCOVER,AUTOEDGE,AUTOPTP>
ifmaxaddr 0 port 4 priority 128 path cost 2000000
member: wlan0 flags=143<LEARNING,DISCOVER,AUTOEDGE,AUTOPTP>
ifmaxaddr 0 port 5 priority 128 path cost 66666
tap0: flags=8943<UP,BROADCAST,RUNNING,PROMISC,SIMPLEX,MULTICAST>
metric 0 mtu 1500
options=80000<LINKSTATE>
ether 00:bd:b1:16:00:00
nd6 options=29<PERFORMNUD,IFDISABLED,AUTO_LINKLOCAL>
media: Ethernet autoselect
status: active
Opened by PID 1918
wlan0: flags=8943<UP,BROADCAST,RUNNING,PROMISC,SIMPLEX,MULTICAST>
metric 0 mtu 1500
ether 74:2f:68:cb:d6:2a
inet 192.168.8.101 netmask 0xffffff00 broadcast 192.168.8.255
nd6 options=29<PERFORMNUD,IFDISABLED,AUTO_LINKLOCAL>
media: IEEE 802.11 Wireless Ethernet MCS mode 11ng
status: associated
ssid HUAWEI-7DC4 channel 1 (2412 MHz 11g ht/20) bssid
94:fe:22:5c:7d:c4
regdomain 96 indoor ecm authmode WPA2/802.11i privacy ON
deftxkey UNDEF AES-CCM 2:128-bit txpower 20 bmiss 7 scanvalid 60
protmode CTS ampdulimit 64k ampdudensity 8 shortgi wme burst
roaming MANUAL
I am using the following commands to load the kernel:
grub-bhyve -m device.map -r hd0,msdos1 -M 2048 centos
ls (hd0,msdos1)/
linux (hd0,msdos1)/vmlinuz-2.6.32-642.el6.x86_64
root=/dev/mapper/VolGroup-lv_root
initrd (hd0,msdos1)/initramfs-2.6.32-642.el6.x86_64.img
boot
and start the guest:
bhyve -c 4 -m 2048M -A -H -P \
-s 0:0,hostbridge \
-s 1:0,lpc \
-s 2:0,virtio-net,tap0 \
-s 3:0,virtio-blk,/dev/zvol/tank4/centos6v \
-l com1,stdio \
centos
The following has been added to /etc/rc.conf:
cloned_interfaces="bridge0 tap0"
ifconfig_bridge0="addm wlan0 addm tap0"
/boot/loader.conf
vmm_load="YES"
nmdm_load="YES"
if_bridge_load="YES"
if_tap_load="YES"
What I am missing?
Grzegorz
I tried to set up the network following this guide:
http://www.krizna.com/centos/how-to-setup-network-in-centos-6/
The dhcp option didn't work (can't obtain the IP). When assigning the IP
statically the network can be started but then only the host is visible.
Neither the DNS nor the gateway are visible:
[root@localhost network-scripts]# pwd
/etc/sysconfig/network-scripts
[root@localhost network-scripts]# cat ifcfg-eth0
DEVICE=eth0
HWADDR=00:A0:98:54:5C:86
TYPE=Ethernet
UUID=d8a635d0-dd47-4d50-ba34-63076ba00775
ONBOOT=yes
NM_CONTROLLED=yes
BOOTPROTO="static"
IPADDR=192.168.8.120
NETMASK=255.255.255.0
GATEWAY=192.168.8.1
DNS1=8.8.8.8
DNS2=4.2.2.2
[root@localhost network-scripts]# ping 192.168.8.101
PING 192.168.8.101 (192.168.8.101) 56(84) bytes of data.
64 bytes from 192.168.8.101: icmp_seq=1 ttl=64 time=0.450 ms
64 bytes from 192.168.8.101: icmp_seq=2 ttl=64 time=0.197 ms
--- 192.168.8.101 ping statistics ---
2 packets transmitted, 2 received, 0% packet loss, time 1640ms
rtt min/avg/max/mdev = 0.197/0.323/0.450/0.127 ms
[root@localhost network-scripts]# ping 8.8.8.8
PING 8.8.8.8 (8.8.8.8) 56(84) bytes of data.
From 192.168.8.120 icmp_seq=1 Destination Host Unreachable
From 192.168.8.120 icmp_seq=2 Destination Host Unreachable
From 192.168.8.120 icmp_seq=3 Destination Host Unreachable
--- 8.8.8.8 ping statistics ---
4 packets transmitted, 0 received, +3 errors, 100% packet loss, time 3341ms
pipe 3
[root@localhost network-scripts]# ping 192.168.8.1
PING 192.168.8.1 (192.168.8.1) 56(84) bytes of data.
From 192.168.8.120 icmp_seq=1 Destination Host Unreachable
From 192.168.8.120 icmp_seq=2 Destination Host Unreachable
From 192.168.8.120 icmp_seq=3 Destination Host Unreachable
--- 192.168.8.1 ping statistics ---
4 packets transmitted, 0 received, +3 errors, 100% packet loss, time 3395ms
pipe 3
Am I missing some additional setting on the host?
Grzegorz
_______________________________________________
freebsd-virtualization@freebsd.org mailing list
https://lists.freebsd.org/mailman/listinfo/freebsd-virtualization
To unsubscribe, send any mail to
"freebsd-virtualization-unsubscr...@freebsd.org"