Just a single file. I'm running a single instance of hostapd, like this: /sbin/hostapd -B /etc/hostapd.conf
op 03-06-14 20:40, Adrian Chadd schreef: > Is hat in one config file? Or two hostapd config files? > > > > -a > > > On 3 June 2014 11:30, Harm Weites <h...@weites.com> wrote: >> Hi, >> >> While trying to setup an AP with two SSID's I ran into some issues. >> >> Environment: >> TP-Link 1043ND (MIPS) >> ath0 ether 00:19:e0:66:66:68 >> wlan0 ether 02:ab:cd:ef:12:30 >> wlan1 ether 00:19:e0:66:66:68 >> >> Both wlan0 and wlan1 have been created with wlandev ath0 and wlanmode >> hostap. The goal is to have one guest wifi network, locked down using pf >> and having a proper wifi network using radius for personal use (thus, >> without pf). >> >> This is the hostapd config: >> >> # >> ctrl_interface=/var/run/hostapd >> hw_mode=g >> >> bss=wlan0 >> interface=wlan0 >> driver=bsd >> ssid=gasten >> wpa=3 >> wpa_key_mgmt=WPA-PSK >> wpa_passphrase=comegetsome >> wpa_pairwise=CCMP >> >> bss=wlan1 >> driver=bsd >> ssid=prive >> wpa=1 >> wpa_key_mgmt=WPA-EAP >> wpa_pairwise=TKIP >> wpa_group_rekey=300 >> wpa_gmk_rekey=640 >> ieee8021x=1 >> auth_algs=1 >> eapol_key_index_workaround=1 >> own_ip_addr=127.0.0.1 >> nas_identifier=wifi.example.com >> auth_server_addr=10.65.0.130 >> auth_server_port=1812 >> auth_server_shared_secret=secret >> acct_server_addr=10.65.0.130 >> acct_server_port=1813 >> acct_server_shared_secret=secret >> # >> >> Now, hostapd complains about the following: >> >> Configuration file: /etc/hostapd.conf >> Using interface wlan0 with hwaddr 02:ab:cd:ef:12:30 and ssid "gasten" >> Failed to add BSS (BSSID=02:ab:cd:ef:12:31) >> wlan0: Unable to setup interface. >> Failed to remove BSS interface wlan0 >> >> Thats it for having multiple (2) SSID's. >> >> Now, the 2nd issue: radius. For this, I've disabled the passphrase'd >> SSID to have just one (working) SSID. >> >> I haven't given the backend much attention just yet, but I'm seeing the >> following error after trying to associate: >> >> wlan0: STA a8:16:b2:54:9c:ef IEEE 802.11: associated >> wlan0: CTRL-EVENT-EAP-STARTED a8:16:b2:54:9c:ef >> wlan0: CTRL-EVENT-EAP-PROPOSED-METHOD vendor=0 method=1 >> wlan0: STA a8:16:b2:54:9c:ef IEEE 802.11: disassociated >> ioctl[SIOCS80211, op=20, val=0, arg_len=7]: No such file or directory >> ioctl[SIOCS80211, op=20, val=0, arg_len=7]: No such file or directory >> >> This is using an Android device, with PEAP. I haven't got a clue yet on >> which mode I should be using, or how to configure that but since I'm >> seeing a 'No such file or directory' I'm afraid something needs to be >> resolved before diving into the final configuration (if this was about >> cert/key files, shouldn't it just explicitly say it's missing just >> that?). Attached to this message is some debug output from hostapd from >> the connection attempt. >> >> Regards, >> Harm >> _______________________________________________ >> firstname.lastname@example.org mailing list >> http://lists.freebsd.org/mailman/listinfo/freebsd-wireless >> To unsubscribe, send any mail to "freebsd-wireless-unsubscr...@freebsd.org" _______________________________________________ email@example.com mailing list http://lists.freebsd.org/mailman/listinfo/freebsd-wireless To unsubscribe, send any mail to "freebsd-wireless-unsubscr...@freebsd.org"