voce tambem precisa dos modulos ndis (if_ndis) e dependencias carregados, ou disponiveis para autoload.
On Thu, 24 Apr 2008 16:44:45 -0300, "Marcos Jesus Faria" <[EMAIL PROTECTED]> wrote: > Fiz o que falou, subi o modulo que ele cria. bcmw15_sys.ko e ficou asism: > > note-marcos# kldstat > Id Refs Address Size Name > 1 11 0xc0400000 9851fc kernel > 2 1 0xc0d86000 6a32c acpi.ko > 3 1 0xc48c6000 130000 bcmwl5_sys.ko > 4 1 0xc4a36000 6000 i915.ko > 5 1 0xc4a3c000 f000 drm.ko > note-marcos# > > Ou seja, carregado o módulo, MAS, ainda não achou meu driver. Acredito > que > esse ai não serve. :( > > > note-marcos# cd /driver/ > note-marcos# ls > Setup.exe bcm43xx.cat > bcmwl5.sys sp36684.cva > Wireless_Broadcom-802BGB/ bcm43xx64.cat > bcmwl564.sys sp36684.exe > Wireless_Broadcom_Vista/ bcmwl5.inf > bcmwl5_sys.ko* wifi_xp/ > note-marcos# ifconfig > bge0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> metric 0 mtu 1500 > options=9b<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,VLAN_HWCSUM> > ether 00:16:d3:e3:4d:9c > inet 192.168.10.187 netmask 0xffffff00 broadcast 192.168.10.255 > media: Ethernet autoselect (1000baseTX <full-duplex>) > status: active > fwe0: flags=8802<BROADCAST,SIMPLEX,MULTICAST> metric 0 mtu 1500 > options=8<VLAN_MTU> > ether 02:0a:e4:60:5c:70 > ch 1 dma -1 > fwip0: flags=8802<BROADCAST,SIMPLEX,MULTICAST> metric 0 mtu 1500 > lladdr 0.a.e4.7.32.60.5c.70.a.2.ff.fe.0.0.0.0 > lo0: flags=8049<UP,LOOPBACK,RUNNING,MULTICAST> metric 0 mtu 16384 > inet6 fe80::1%lo0 prefixlen 64 scopeid 0x4 > inet6 ::1 prefixlen 128 > inet 127.0.0.1 netmask 0xff000000 > note-marcos# > > > On Wed, Apr 23, 2008 at 7:02 PM, Carlos A. M. dos Santos < > [EMAIL PROTECTED]> wrote: > >> 2008/4/23 Marcos Jesus Faria <[EMAIL PROTECTED]>: >> > ok... >> > >> > Executei os comandos baseado na explicação >> > > http://www.freebsd.org/doc/en/books/handbook/config-network-setup.html >> > >> > # ndisgen bcmw16.inf bcmw16.sys >> > >> > e da erro na compilação. >> > >> > ./windrv.h:2531: error: extra brace group at end of initializer >> > ./windrv.h:2531: error: (near initialization for 'ndis_regvals[453]') >> > ./windrv.h:2533: error: extra brace group at end of initializer >> > ./windrv.h:2533: error: (near initialization for 'ndis_regvals[453]') >> > ./windrv.h:2534: error: extra brace group at end of initializer >> > ./windrv.h:2534: error: (near initialization for 'ndis_regvals[453]') >> > ./windrv.h:2536: error: extra brace group at end of initializer >> > ./windrv.h:2536: error: (near initialization for 'ndis_regvals[453]') >> > ./windrv.h:2537: error: extra brace group at end of initializer >> > ./windrv.h:2537: error: (near initialization for 'ndis_regvals[453]') >> > ./windrv.h:2539: error: extra brace group at end of initializer >> > ./windrv.h:2539: error: (near initialization for 'ndis_regvals[453]') >> > ./windrv.h:2540: error: extra brace group at end of initializer >> > ./windrv.h:2540: error: (near initialization for 'ndis_regvals[453]') >> > ./windrv.h:2540: error: extra brace group at end of initializer >> > ./windrv.h:2540: error: (near initialization for 'ndis_regvals[453]') >> > ./windrv.h:2541: error: expected '}' before ';' token >> > build failed. Exiting. >> > >> > Tentei com o driver do Xp e do Vista, ambos i386. >> > >> > Alguma outra dica.. >> >> Baixa o driver fornecido pela HP para os notebooks Pavilion: >> >> ftp://ftp.hp.com/pub/softpaq/sp36501-37000/sp36684.exe >> >> Instala o pacote "cabextract" (archivers/cabextract). >> >> Depois: >> >> cabextract sp36684.exe >> ndisgen bcmwl5.inf bcmwl5.sys >> >> -- >> Carlos A. M. dos Santos >> ------------------------- >> Histórico: http://www.fug.com.br/historico/html/freebsd/ >> Sair da lista: https://www.fug.com.br/mailman/listinfo/freebsd >> > > > > ------------------------- Histórico: http://www.fug.com.br/historico/html/freebsd/ Sair da lista: https://www.fug.com.br/mailman/listinfo/freebsd
