Hello UAFUG,
Добрый день сообществу!
Возникла проблема: есть сервер HP Proliant ML 110 G6, укомплектован
двумя двухголовыми картами HP NC382T PCIe DP Multifunction Gigabit
Server Adapter (опознаются как bce(4)) + одна карта встроенная
(HP NC107i PCIe Gigabit Server Adapter, bge(4)). Обслуживает небольшую
сеть филиала предприятия, примерно на 100 клиентов. Задачи разные - то
интернет, то впн в различных позах. Система FreeBSD 8.3-PRERELEASE #5.
Пока интернет был относительно слабым (DSL от *телекома, pppoe от
мобильщиков) всё работало нормально. Недавно кинули нам оптику, с
обещанием до 100 Мб, воткнул во второй порт сетевушки, пропинговал
шлюз, перекидываю маршрут - через пять секунд сервер перезагружается
без каких-либо сообщений в консоли. Дальнейшие игры стабильно
приводили к такому же результату. Пытался втыкать в порты другой
сетевухи - после смены маршрута стабильно или перезагружается, или
выпадает из сети, переставая откликаться на любые внешние
раздражители. На консоли - никаких проблем не высвечивает. С просто
воткнутым кабелем в гнёзда сетевых карт - работает неделями. Однако, в
последнее время наш *телеком часто колбасит. :(
Куда копать, подскажите, плз?
ЗЫ: Сервер в бою, заменить пока нечем, эксперименты посреди рабочего
дня приводят к шквалу звонков. :(
dmesg:
FreeBSD is a registered trademark of The FreeBSD Foundation.
FreeBSD 8.3-PRERELEASE #5: Tue Apr 3 00:06:41 EEST 2012
[email protected]:/usr/obj/usr/opt/src/sys/HP110 i386
Timecounter "i8254" frequency 1193182 Hz quality 0
CPU: Intel(R) Pentium(R) CPU G6950 @ 2.80GHz (2980.52-MHz 686-class CPU)
Origin = "GenuineIntel" Id = 0x20652 Family = 6 Model = 25 Stepping = 2
Features=0xbfebfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,C
MOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE>
Features2=0x80e3bd<SSE3,DTES64,MON,DS_CPL,VMX,EST,TM2,SSSE3,CX16,xTPR,PDCM,POP
CNT>
AMD Features=0x28100000<NX,RDTSCP,LM>
AMD Features2=0x1<LAHF>
TSC: P-state invariant
real memory = 2147483648 (2048 MB)
avail memory = 2086916096 (1990 MB)
ACPI APIC Table: <HP ProLiant>
FreeBSD/SMP: Multiprocessor System Detected: 2 CPUs
FreeBSD/SMP: 1 package(s) x 2 core(s)
cpu0 (BSP): APIC ID: 0
cpu1 (AP): APIC ID: 4
ioapic0 <Version 2.0> irqs 0-23 on motherboard
kbd0 at kbdmux0
acpi0: <HP ProLiant> on motherboard
acpi0: [ITHREAD]
acpi0: Power Button (fixed)
Timecounter "ACPI-fast" frequency 3579545 Hz quality 1000
acpi_timer0: <24-bit timer at 3.579545MHz> port 0x1008-0x100b on acpi0
cpu0: <ACPI CPU> on acpi0
cpu1: <ACPI CPU> on acpi0
pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
pci0: <ACPI PCI bus> on pcib0
pcib1: <ACPI PCI-PCI bridge> irq 16 at device 1.0 on pci0
pci1: <ACPI PCI bus> on pcib1
ehci0: <Intel PCH USB 2.0 controller USB-B> mem 0xdcc02000-0xdcc023ff irq 16 at
device 26.0 on pci0
ehci0: [ITHREAD]
usbus0: EHCI version 1.0
usbus0 on ehci0
pcib2: <ACPI PCI-PCI bridge> irq 17 at device 28.0 on pci0
pci16: <ACPI PCI bus> on pcib2
bce0: <HP NC382T PCIe DP Multifunction Gigabit Server Adapter (C0)> mem
0xd4000000-0xd5ffffff irq 16 at device 0.0 on pci16
miibus0: <MII bus> on bce0
brgphy0: <BCM5709C 10/100/1000baseTX PHY> PHY 1 on miibus0
brgphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT,
1000baseT-master, 1000baseT-FDX, 1000baseT-FDX-master, auto, auto-flow
bce0: Ethernet address: 68:b5:99:bc:aa:60
bce0: [ITHREAD]
bce0: ASIC (0x57092003); Rev (C0); Bus (PCIe x1, 2.5Gbps); B/C (5.2.3); Bufs
(RX:2;TX:2;PG:8); Flags (SPLT|MSI)
Coal (RX:6,6,18,18; TX:20,20,80,80)
bce1: <HP NC382T PCIe DP Multifunction Gigabit Server Adapter (C0)> mem
0xd6000000-0xd7ffffff irq 17 at device 0.1 on pci16
miibus1: <MII bus> on bce1
brgphy1: <BCM5709C 10/100/1000baseTX PHY> PHY 1 on miibus1
brgphy1: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT,
1000baseT-master, 1000baseT-FDX, 1000baseT-FDX-master, auto, auto-flow
bce1: Ethernet address: 68:b5:99:bc:aa:62
bce1: [ITHREAD]
bce1: ASIC (0x57092003); Rev (C0); Bus (PCIe x1, 2.5Gbps); B/C (5.2.3); Bufs
(RX:2;TX:2;PG:8); Flags (SPLT|MSI)
Coal (RX:6,6,18,18; TX:20,20,80,80)
pcib3: <ACPI PCI-PCI bridge> irq 16 at device 28.1 on pci0
pci26: <ACPI PCI bus> on pcib3
pcib4: <ACPI PCI-PCI bridge> irq 18 at device 28.2 on pci0
pci28: <ACPI PCI bus> on pcib4
vgapci0: <VGA-compatible display> mem
0xdd000000-0xddffffff,0xdc800000-0xdc803fff,0xdc000000-0xdc7fffff irq 18 at
device 0.0 on pci28
pcib5: <ACPI PCI-PCI bridge> irq 19 at device 28.3 on pci0
pci30: <ACPI PCI bus> on pcib5
bge0: <HP NC107i PCIe Gigabit Server Adapter, ASIC rev. 0x5784100> mem
0xdc900000-0xdc90ffff irq 19 at device 0.0 on pci30
bge0: CHIP ID 0x05784100; ASIC REV 0x5784; CHIP REV 0x57841; PCI-E
miibus2: <MII bus> on bge0
brgphy2: <BCM5784 10/100/1000baseTX PHY> PHY 1 on miibus2
brgphy2: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT,
1000baseT-master, 1000baseT-FDX, 1000baseT-FDX-master, auto, auto-flow
bge0: Ethernet address: d4:85:64:3a:6b:8c
bge0: [FILTER]
pcib6: <ACPI PCI-PCI bridge> irq 17 at device 28.4 on pci0
pci32: <ACPI PCI bus> on pcib6
bce2: <HP NC382T PCIe DP Multifunction Gigabit Server Adapter (C0)> mem
0xd8000000-0xd9ffffff irq 16 at device 0.0 on pci32
miibus3: <MII bus> on bce2
brgphy3: <BCM5709C 10/100/1000baseTX PHY> PHY 1 on miibus3
brgphy3: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT,
1000baseT-master, 1000baseT-FDX, 1000baseT-FDX-master, auto, auto-flow
bce2: Ethernet address: 68:b5:99:bc:c9:94
bce2: [ITHREAD]
bce2: ASIC (0x57092003); Rev (C0); Bus (PCIe x4, 2.5Gbps); B/C (5.2.3); Bufs
(RX:2;TX:2;PG:8); Flags (SPLT|MSI)
Coal (RX:6,6,18,18; TX:20,20,80,80)
bce3: <HP NC382T PCIe DP Multifunction Gigabit Server Adapter (C0)> mem
0xda000000-0xdbffffff irq 17 at device 0.1 on pci32
miibus4: <MII bus> on bce3
brgphy4: <BCM5709C 10/100/1000baseTX PHY> PHY 1 on miibus4
brgphy4: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT,
1000baseT-master, 1000baseT-FDX, 1000baseT-FDX-master, auto, auto-flow
bce3: Ethernet address: 68:b5:99:bc:c9:96
bce3: [ITHREAD]
bce3: ASIC (0x57092003); Rev (C0); Bus (PCIe x4, 2.5Gbps); B/C (5.2.3); Bufs
(RX:2;TX:2;PG:8); Flags (SPLT|MSI)
Coal (RX:6,6,18,18; TX:20,20,80,80)
ehci1: <Intel PCH USB 2.0 controller USB-A> mem 0xdcc02400-0xdcc027ff irq 23 at
device 29.0 on pci0
ehci1: [ITHREAD]
usbus1: EHCI version 1.0
usbus1 on ehci1
pcib7: <ACPI PCI-PCI bridge> at device 30.0 on pci0
pci48: <ACPI PCI bus> on pcib7
isab0: <PCI-ISA bridge> at device 31.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <Intel 5 Series/3400 Series PCH SATA300 controller> port
0x1830-0x1837,0x1824-0x1827,0x1828-0x182f,0x1820-0x1823,0x1800-0x181f mem
0xdcc01000-0xdcc017ff irq 18 at device 31.2 on pci0
atapci0: [ITHREAD]
atapci0: AHCI called from vendor specific driver
atapci0: AHCI v1.30 controller with 6 3Gbps ports, PM supported
ata2: <ATA channel> at channel 0 on atapci0
ata2: [ITHREAD]
ata3: <ATA channel> at channel 1 on atapci0
ata3: [ITHREAD]
ata4: <ATA channel> at channel 2 on atapci0
ata4: port is not ready (timeout 15000ms) tfd = 00000080
ata4: hardware reset timeout
ata4: [ITHREAD]
ata5: <ATA channel> at channel 3 on atapci0
ata5: [ITHREAD]
ata6: <ATA channel> at channel 4 on atapci0
ata6: [ITHREAD]
ata7: <ATA channel> at channel 5 on atapci0
ata7: [ITHREAD]
pci0: <serial bus, SMBus> at device 31.3 (no driver attached)
ipmi0: <IPMI System Interface> port 0xca2-0xca3 on acpi0
ipmi0: KCS mode found at io 0xca2 on acpi
acpi_button0: <Power Button> on acpi0
acpi_hpet0: <High Precision Event Timer> iomem 0xfed00000-0xfed003ff irq 0,8 on
acpi0
Timecounter "HPET" frequency 14318180 Hz quality 900
atrtc0: <AT realtime clock> port 0x70-0x71 on acpi0
pmtimer0 on isa0
ipmi1: <IPMI System Interface> on isa0
device_attach: ipmi1 attach returned 16
ipmi1: <IPMI System Interface> on isa0
device_attach: ipmi1 attach returned 16
orm0: <ISA Option ROMs> at iomem
0xc0000-0xc7fff,0xc8000-0xc8fff,0xdf000-0xdffff pnpid ORM0000 on isa0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
ata0: <ATA channel> at port 0x1f0-0x1f7,0x3f6 irq 14 on isa0
ata0: [ITHREAD]
ata1: <ATA channel> at port 0x170-0x177,0x376 irq 15 on isa0
ata1: [ITHREAD]
coretemp0: <CPU On-Die Thermal Sensors> on cpu0
coretemp1: <CPU On-Die Thermal Sensors> on cpu1
Timecounters tick every 1.000 msec
usbus0: 480Mbps High Speed USB v2.0
usbus1: 480Mbps High Speed USB v2.0
ugen0.1: <Intel> at usbus0
uhub0: <Intel EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus0
ugen1.1: <Intel> at usbus1
uhub1: <Intel EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus1
ad4: 238475MB <WDC WD2500AAKX-001CA0 15.01H15> at ata2-master UDMA100 SATA 3Gb/s
ad8: 238475MB <WDC WD2500AAKX-001CA0 15.01H15> at ata4-master UDMA100 SATA 3Gb/s
GEOM_MIRROR: Device mirror/gm0 launched (1/2).
GEOM_MIRROR: Device gm0: rebuilding provider ad4.
acd0: DVDROM <hp DVDROM DH20N/EB00> at ata6-master UDMA100 SATA 1.5Gb/s
ipmi0: IPMI device rev. 1, firmware rev. 4.06, version 2.0
ipmi0: Number of channels 1
ipmi0: Attached watchdog
SMP: AP CPU #1 Launched!
GEOM_PART: integrity check failed (mirror/gm0, MBR)
GEOM: mirror/gm0s1: geometry does not match label (16h,63s != 255h,63s).
uhub0: 2 ports with 2 removable, self powered
uhub1: 2 ports with 2 removable, self powered
Root mount waiting for: usbus1 usbus0
ugen0.2: <vendor 0x8087> at usbus0
uhub2: <vendor 0x8087 product 0x0020, class 9/0, rev 2.00/0.00, addr 2> on
usbus0
ugen1.2: <vendor 0x8087> at usbus1
uhub3: <vendor 0x8087 product 0x0020, class 9/0, rev 2.00/0.00, addr 2> on
usbus1
Root mount waiting for: usbus1 usbus0
uhub2: 6 ports with 6 removable, self powered
uhub3: 6 ports with 6 removable, self powered
ugen1.3: <ServerEngines> at usbus1
Root mount waiting for: usbus1
ugen1.4: <Pantech, Incorporated> at usbus1
Trying to mount root from ufs:/dev/mirror/gm0s1a
kbd1 at ukbd0
ums0: <ServerEngines SE USB Device, class 0/0, rev 1.10/0.01, addr 3> on usbus1
ums0: 8 buttons and [XYZ] coordinates ID=0
ifconfig:
bce0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> metric 0 mtu 1500
options=c01bb<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,JUMBO_MTU,VLAN_HWCSUM,TSO4,VLAN_HWTSO,LINKSTATE>
ether 68:b5:99:bc:aa:60
media: Ethernet autoselect (100baseTX
<full-duplex,flowcontrol,rxpause,txpause>)
status: active
bce1: flags=8802<BROADCAST,SIMPLEX,MULTICAST> metric 0 mtu 1500
options=c01bb<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,JUMBO_MTU,VLAN_HWCSUM,TSO4,VLAN_HWTSO,LINKSTATE>
ether 68:b5:99:bc:aa:62
media: Ethernet autoselect
bge0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> metric 0 mtu 1500
options=c019b<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,VLAN_HWCSUM,TSO4,VLAN_HWTSO,LINKSTATE>
ether d4:85:64:3a:6b:8c
inet 192.168.0.251 netmask 0xffffff00 broadcast 192.168.0.255
inet 192.168.15.1 netmask 0xfffffff0 broadcast 192.168.15.15
inet 192.168.4.1 netmask 0xffffff00 broadcast 192.168.4.255
inet 192.168.10.1 netmask 0xffffff80 broadcast 192.168.10.127
media: Ethernet autoselect (100baseTX
<full-duplex,flowcontrol,rxpause,txpause>)
status: active
bce2: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> metric 0 mtu 1500
options=c01bb<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,JUMBO_MTU,VLAN_HWCSUM,TSO4,VLAN_HWTSO,LINKSTATE>
ether 68:b5:99:bc:c9:94
inet 178.219.247.22 netmask 0xfffffffc broadcast 178.219.247.23
media: Ethernet autoselect (100baseTX
<full-duplex,flowcontrol,rxpause,txpause>)
status: active
bce3: flags=8802<BROADCAST,SIMPLEX,MULTICAST> metric 0 mtu 1500
options=c01bb<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,JUMBO_MTU,VLAN_HWCSUM,TSO4,VLAN_HWTSO,LINKSTATE>
ether 68:b5:99:bc:c9:96
media: Ethernet autoselect
ipfw0: flags=8801<UP,SIMPLEX,MULTICAST> metric 0 mtu 65536
lo0: flags=8049<UP,LOOPBACK,RUNNING,MULTICAST> metric 0 mtu 16384
options=3<RXCSUM,TXCSUM>
inet 127.0.0.1 netmask 0xff000000
ng0: flags=88d1<UP,POINTOPOINT,RUNNING,NOARP,SIMPLEX,MULTICAST> metric 0 mtu
1492
inet 10.100.2.109 --> 10.100.0.1 netmask 0xffffffff
tun0: flags=8051<UP,POINTOPOINT,RUNNING,MULTICAST> metric 0 mtu 1500
options=80000<LINKSTATE>
inet 192.168.5.22 --> 192.168.5.21 netmask 0xffffffff
Opened by PID 3759
--
Best regards,
Alexander mailto:[email protected]
