https://www.linkedin.com/in/david-germiquet-2a653313/
this is not phishing im nervous Your Friendly Turtle, of Western Ontario Oogway ‐‐‐‐‐‐‐ Original Message ‐‐‐‐‐‐‐ On Thursday, May 13th, 2021 at 10:39 PM, Sunil Mohan Adapa <[email protected]> wrote: > On 13/05/21 9:31 am, Navi Singh wrote: > > > Hi Dear, > > > > Greetings!! > > > > Currently, I'm testing freedombox with my Raspberry pi 400, and first of > > > > all, I would like to explain about my freedombox setup. > > > > 1. SD card with UEFI Firmware > > 2. USB type 3.0 with freedombox image > > 3. Ethernet Cable > > 4. LED with HDMI cable. > > > > the first time, it is being executed, but when I try to restart with > > > > both SD card and USB. its reaches to the grub recuse> > > > > *with Grub rescuse > * if I use ls, set root, set prefix etc it is being > > > > done successfully, but again when I tried to do *insmod normal *and > > > > normal, both are showing an error. > > You may be facing a bug in grub[1]. Before you reboot, please try > > installing 'shim-signed', 'shim-helpers-arm64-signed', > > 'shim-signed-common' and 'shim-unsigned' packages. If that does not > > work, please uninstall the grub* packages and re-install them. This > > worked for me. > > > So my question is that, how can I resolve the restart case, and how can > > > > I put UEFI firmware & freedombox USB in a single drive, because there is > > > > no response if I remove SD card. > > The SD contains the UEFI firmware in the format understood by Raspberry > > Pi. The USB drive contains EFI partition and the root partition. You can > > to combine them manually by copying the EFI and root partitions to SD > > card. It is likely to work without any further changes. > > On official images, we can't distribute the UEFI firmware due to be > > binaries it it and we are trying not to create a separate image for each > > of the single board computers. > > > http://deb.debian.org/debian/pool/main/p/python-colorama/python3-colorama_0.4.4-1_all.deb > > > > http://deb.debian.org/debian/pool/main/p/python-colorama/python3-colorama_0.4.4-1_all.deb > > > > Could not resolve 'debian.map.fastlydns.net > > > > http://debian.map.fastlydns.net' Cannot initiate the connection to > > > > deb.debian.org:80 http://deb.debian.org:80 (2a04:4e42:48::644). - > > > > connect (101: Network is unreachable) Could not connect to > > > > deb.debian.org:80 http://deb.debian.org:80 (199.232.46.132), > > > > connection timed out E: Failed to fetch > > If your FreedomBox is able to access network in general but not able to > > do install apps, then it could be a problem with IPv6 configuration in > > your network. Try setting IPv6 configuration to "Ignored" using > > FreedomBox interface, nmtui tool or nmcli too. > > Links: > > 1. https://bugs.debian.org/cgi-bin/bugreport.cgi?bug=984760 > > -- > > Sunil > > Freedombox-discuss mailing list > > [email protected] > > https://alioth-lists.debian.net/cgi-bin/mailman/listinfo/freedombox-discuss _______________________________________________ Freedombox-discuss mailing list [email protected] https://alioth-lists.debian.net/cgi-bin/mailman/listinfo/freedombox-discuss
