On Fri, Apr 13, 2018 at 10:53:01AM +0530, Sandeep Panda wrote:
> Document the bindings used for the sn65dsi86 DSI to eDP bridge.
> 
> Signed-off-by: Sandeep Panda <spa...@codeaurora.org>
> ---
>  .../bindings/display/bridge/ti,sn65dsi86.txt       | 75 
> ++++++++++++++++++++++
>  1 file changed, 75 insertions(+)
>  create mode 100644 
> Documentation/devicetree/bindings/display/bridge/ti,sn65dsi86.txt
> 
> diff --git 
> a/Documentation/devicetree/bindings/display/bridge/ti,sn65dsi86.txt 
> b/Documentation/devicetree/bindings/display/bridge/ti,sn65dsi86.txt
> new file mode 100644
> index 0000000..cbd2f0e
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/display/bridge/ti,sn65dsi86.txt
> @@ -0,0 +1,75 @@
> +SN65DSI86 DSI to eDP bridge chip
> +--------------------------------
> +
> +This is the binding for Texas Instruments SN65DSI86 bridge.
> +
> +Required properties:
> +- compatible: Must be "ti,sn65dsi86"
> +- reg: i2c address of the chip, 0x2d as per datasheet
> +- enable-gpios: OF device-tree gpio specification for EDP_BRIJ_EN pin
> +- aux-sda-gpios: OF device-tree gpio specification for EDP_BRIJ_I2C_SDA pin 
> of AUX channel
> +- aux-scl-gpios: OF device-tree gpio specification for EDP_BRIJ_I2C_SCL pin 
> of AUX channel

What if I use I2C host on my device? If your board design uses bitbanged 
I2C, that is outside the scope of this binding and it should use 
i2c-gpio binding.

> +- bias-en-gpios: OF device-tree gpio specification for EN_PP3300_DX_EDP pin 
> to
> +                     enable 3.3V supply to eDP connector
> +- bklt-en-gpios: OF device-tree gpio specification for AP_EDP_BKLTEN 
pin
> +
> +- vccio-supply: A 1.8V supply that powers up the PHY.
> +- vcca-supply: A 1.2V supply that powers up the Controller.
> +- vccs-supply: A 3.3V supply that power the eDP connector
> +
> +Optional properties:
> +
> +- irq-gpios: OF device-tree gpio specification for interrupt pin

Use "interrupts" property instead.

> +- bklt-ctrl-gpios: OF device-tree gpio specification for EDP_BKLTCTL pin
> +
> +- sn,is-pluggable: boolean property to specify if HPD supported or not
> +- sn,custom-modes: OF device-tree specifiction to add support for custom 
> modes

"sn" is not a vendor.

> +
> +Required nodes:
> +
> +This device has two video ports. Their connections are modelled using the OF
> +graph bindings specified in Documentation/devicetree/bindings/graph.txt.
> +
> +- Video port 0 for DSI input
> +- Video port 1 for eDP output
> +
> +Example
> +-------
> +
> +edp-bridge@2d {
> +     compatible = "ti,sn65dsi86";
> +     #address-cells = <1>;
> +     #size-cells = <0>;
> +     reg = <0x2d>;
> +
> +     enable-gpios = <&msmgpio 33 GPIO_ACTIVE_HIGH>;
> +     aux-sda-gpios = <&msmgpio 34 GPIO_ACTIVE_HIGH>;
> +     aux-scl-gpios = <&msmgpio 35 GPIO_ACTIVE_HIGH>;
> +     bias-en-gpios = <&msmgpio 36 GPIO_ACTIVE_HIGH>;
> +     bklt-en-gpios = <&msmgpio 37 GPIO_ACTIVE_HIGH>;
> +
> +     vccio-supply = <&pm8916_l17>;
> +     vcca-supply = <&pm8916_l6>;
> +     vccs-supply = <&pm8916_l7>;
> +
> +     ports {
> +             #address-cells = <1>;
> +             #size-cells = <0>;
> +
> +             port@0 {
> +                     reg = <0>;
> +
> +                     edp_bridge_in: endpoint {
> +                             remote-endpoint = <&dsi_out>;
> +                     };
> +             };
> +
> +             port@1 {
> +                     reg = <1>;
> +
> +                     edp_bridge_out: endpoint {
> +                             remote-endpoint = <&edp_panel_in>;
> +                     };
> +             };
> +     };
> +}
> -- 
> The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
> a Linux Foundation Collaborative Project
> 
> --
> To unsubscribe from this list: send the line "unsubscribe devicetree" in
> the body of a message to majord...@vger.kernel.org
> More majordomo info at  http://vger.kernel.org/majordomo-info.html
_______________________________________________
Freedreno mailing list
Freedreno@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/freedreno

Reply via email to