Quoting Sandeep Panda (2018-05-14 22:52:42)
> diff --git
> a/Documentation/devicetree/bindings/display/bridge/ti,sn65dsi86.txt
> b/Documentation/devicetree/bindings/display/bridge/ti,sn65dsi86.txt
> new file mode 100644
> index 0000000..b82bb56
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/display/bridge/ti,sn65dsi86.txt
> @@ -0,0 +1,81 @@
> +Optional properties:
> +- interrupts: Specifier for the SN65DSI86 interrupt line.
> +- hpd-gpios: OF device-tree gpio specifications for HPD pin.
> +
> +- gpio-controller: Marks the device has a GPIO controller.
> +- #gpio-cells : Should be two. The first cell is the pin number and
> + the second cell is used to specify flags.
> + See ../../gpio/gpio.txt for more information.
> +- #pwm-cells : Should be one. See ../../pwm/pwm.txt for description of
> + the cell formats.
> +
> +- clock-names: should be "refclk"
> +- clocks: OF device-tree clock specification for refclk input. The reference
What is "OF device-tree .* specification" providing? This is all an OF
device-tree specification.
> + clock rate must be 12 MHz, 19.2 MHz, 26 MHz, 27 MHz or 38.4 MHz.
> +
> +Required nodes:
> +
> +This device has two video ports. Their connections are modelled using the
> +OF graph bindings specified in Documentation/devicetree/bindings/graph.txt.
> +
> +- Video port 0 for DSI input
> +- Video port 1 for eDP output
> +
> +Example
> +-------
> +
> +edp-bridge@2d {
> + compatible = "ti,sn65dsi86";
> + #address-cells = <1>;
> + #size-cells = <0>;
> + reg = <0x2d>;
> +
> + enable-gpios = <&msmgpio 33 GPIO_ACTIVE_HIGH>;
> + interrupt-parent = <&gpio3>;
> + interrupts = <4 IRQ_TYPE_EDGE_FALLING>;
> +
> + vccio-supply = <&pm8916_l17>;
> + vcca-supply = <&pm8916_l6>;
> + vpll-supply = <&pm8916_l17>;
> + vcc-supply = <&pm8916_l6>;
> +
> + clock-names = "refclk";
> + clocks = <&input_refclk>;
> +
> + ports {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + port@0 {
> + reg = <0>;
> +
> + edp_bridge_in: endpoint {
> + remote-endpoint = <&dsi_out>;
How do we know the number of lanes that are connected and if there's one
channel (A) or two channels (A and B)? Would there be two endpoints in
that case?
> + };
> + };
> +
> + port@1 {
> + reg = <1>;
> +
> + edp_bridge_out: endpoint {
> + remote-endpoint = <&edp_panel_in>;
The hardware looks to support some sort of lane renumbering scheme,
where the eDP logical lane 0 can be routed through a different pin than
MLP/N0, same for logical lane 1, etc. I don't have a use case for this
right now, but I hope that it could be added somewhere in the binding as
an optional property to describe this lane remapping feature. It also
has some sort of lane polarity inversion feature. Perhaps there needs to
be a lane-config property that does this remapping and inversion with
two cells.
lane-config = <0 0>, /* Lane 0 logical is lane 0 phys (!inv) */
<1 0>, /* Lane 1 logical is lane 1 phys (!inv) */
<2 0>, /* Lane 2 logical is lane 2 phys (!inv) */
<3 0>; /* Lane 3 logical is lane 3 phys (!inv) */
Or
lane-config = <2 1>, /* Lane 2 logical is lane 0 phys (inv) */
<1 0>, /* Lane 1 logical is lane 1 phys (!inv) */
<3 1>, /* Lane 3 logical is lane 2 phys (inv) */
<0 0>; /* Lane 0 logical is lane 3 phys (!inv) */
> + };
> + };
> + };
_______________________________________________
Freedreno mailing list
Freedreno@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/freedreno
