On 4/25/2025 2:27 AM, Dmitry Baryshkov wrote:
On Fri, 25 Apr 2025 at 00:00, Abhinav Kumar <[email protected]> wrote:
On 4/24/2025 3:23 AM, Dmitry Baryshkov wrote:
On Wed, Apr 23, 2025 at 07:04:16PM -0700, Abhinav Kumar wrote:
On 2/26/2025 6:25 PM, Dmitry Baryshkov wrote:
LVDS support in MDP4 driver makes use of drm_connector directly. However
LCDC encoder and LVDS connector are wrappers around drm_panel. Switch
them to use drm_panel_bridge/drm_bridge_connector. This allows using
standard interface for the drm_panel and also inserting additional
bridges between encoder and panel.
Signed-off-by: Dmitry Baryshkov <[email protected]>
---
drivers/gpu/drm/msm/Makefile | 1 -
drivers/gpu/drm/msm/disp/mdp4/mdp4_kms.c | 34 +++++--
drivers/gpu/drm/msm/disp/mdp4/mdp4_kms.h | 6 +-
drivers/gpu/drm/msm/disp/mdp4/mdp4_lcdc_encoder.c | 20 +----
.../gpu/drm/msm/disp/mdp4/mdp4_lvds_connector.c | 100
---------------------
5 files changed, 28 insertions(+), 133 deletions(-)
@@ -199,27 +201,43 @@ static int mdp4_modeset_init_intf(struct mdp4_kms
*mdp4_kms,
* bail out early if there is no panel node (no need to
* initialize LCDC encoder and LVDS connector)
*/
- panel_node = of_graph_get_remote_node(dev->dev->of_node, 0, 0);
- if (!panel_node)
- return 0;
+ next_bridge = devm_drm_of_get_bridge(dev->dev, dev->dev->of_node,
0, 0);
+ if (IS_ERR(next_bridge)) {
+ ret = PTR_ERR(next_bridge);
+ if (ret == -ENODEV)
+ return 0;
+ return ret;
+ }
- encoder = mdp4_lcdc_encoder_init(dev, panel_node);
+ encoder = mdp4_lcdc_encoder_init(dev);
if (IS_ERR(encoder)) {
DRM_DEV_ERROR(dev->dev, "failed to construct LCDC
encoder\n");
- of_node_put(panel_node);
return PTR_ERR(encoder);
}
/* LCDC can be hooked to DMA_P (TODO: Add DMA_S later?) */
encoder->possible_crtcs = 1 << DMA_P;
- connector = mdp4_lvds_connector_init(dev, panel_node, encoder);
+ ret = drm_bridge_attach(encoder, next_bridge, NULL,
DRM_BRIDGE_ATTACH_NO_CONNECTOR);
+ if (ret) {
+ DRM_DEV_ERROR(dev->dev, "failed to attach LVDS panel/bridge:
%d\n", ret);
+
+ return ret;
+ }
Can you pls point me to the lvds bridge used with this apq8064 board? I was
unable to find it. Just wanted to compare that against this while reviewing.
It's the panel bridge, wrapping one of the LVDS panels.
Yes but what I wanted to check was which LVDS panel was being used so
far. Looks like for arm32 the dts is missing? As I couldnt find the lvds
out endpoint. So can you pls point me to the lvds panel you verified
this with?
I used the AUO b101xtn01 panel connected to the LVDS connector on the
IFC6410. I'm not posting DT bits since the panel is not a part of the
kit.
Ok, so at this point of time, this is just the driver piece which does
not have a real HW in the tree to be verified with.
+
+ connector = drm_bridge_connector_init(dev, encoder);
if (IS_ERR(connector)) {
DRM_DEV_ERROR(dev->dev, "failed to initialize LVDS
connector\n");
- of_node_put(panel_node);
return PTR_ERR(connector);
}
+ ret = drm_connector_attach_encoder(connector, encoder);
+ if (ret) {
+ DRM_DEV_ERROR(dev->dev, "failed to attach LVDS connector:
%d\n", ret);
+
+ return ret;
+ }
+
break;
case DRM_MODE_ENCODER_TMDS:
encoder = mdp4_dtv_encoder_init(dev);
