Well, a part of the example on the website (FAQ/4.12) is definitely
wrong!
Anyway, a short look to the users file you edited would have solved the
problem, too.
see below
Am Fre, 2003-09-19 um 06.43 schrieb puneeth b:
> hello sir,
> i've already mailed u regarding some doubts,thanks for the
> reply.
>
> i've few more doubts,
> Sir,
> Doubts regarding the freeradius server, kindly help me out.
> As given in section 4.12 of FAQ Debugging it yourself , i did the
> following steps
> -----------------------------------------------------------------------
> Step 1:
> it is given that
> 3. Ensure that you have localhost in your raddb/clients file.
> FreeRADIUS
> comes configured this way, so it should be there.
> so i found entry in
> /usr/local/etc/raddb/clients
> as
> # Client Name Key
> #---------------- ----------
> #portmaster1.isp.com testing123
> #portmaster2.isp.com testing123
> #proxyradius.isp2.com TheirKey
> #localhost testing123
> -----------------------------------------------------------------------
> Step 2:
> 4. Ensure you have a valid user in your raddb/users file. If
> everything else
> fails, go to the top of the file and add the following entry:
> so i did entry in
> /usr/local/etc/raddb/users
> as it was given in the FAQ
> bob Password = "bob"
> i Reply-Message = "Hello, bob"
make it:
bob User-Password == "bob"
Reply-Message = "Hello, bob"
> ------------------------------------------------------------------------
> Step 3:
> it is given that
> 1. Run the server in debugging mode
> radiusd -sfxxyz -l stdout
> i got the message
> Ready to process requests.
> -------------------------------------------------------------------------
> Step 4:
> in another window i ran this command as given in the FAQ
> [EMAIL PROTECTED] root]# radtest bob bob localhost 0 testing123
> Sending Access-Request of id 185 to 127.0.0.1:1812
> User-Name = "bob"
> User-Password = "bob"
> NAS-IP-Address = localhost.localdomain
> NAS-Port = 0
> In the server side I got the below listed messages:
> rad_recv: Access-Request packet from host 127.0.0.1:1025, id=185,
> length=55
> User-Name = "bob"
> User-Password = "bob"
> NAS-IP-Address = 255.255.255.255
> NAS-Port = 0
> modcall: entering group authorize
> modcall[authorize]: module "preprocess" returns ok
> modcall[authorize]: module "chap" returns noop
> rlm_eap: EAP-Message not found
> modcall[authorize]: module "eap" returns noop
> rlm_realm: No '@' in User-Name = "bob", looking up realm NULL
> rlm_realm: No such realm "NULL"
> modcall[authorize]: module "suffix" returns noop
> users: Matched DEFAULT at 153
> modcall[authorize]: module "files" returns ok
> modcall[authorize]: module "mschap" returns noop
> modcall: group authorize returns ok
> rad_check_password: Found Auth-Type System
> auth: type "System"
> modcall: entering group authenticate
> modcall[authenticate]: module "unix" returns notfound
> modcall: group authenticate returns notfound
> auth: Failed to validate the user.
> Delaying request 0 for 1 seconds
> Finished request 0
> Going to the next request
> --- Walking the entire request list ---
> Waking up in 1 seconds...
> --- Walking the entire request list ---
> Waking up in 1 seconds...
> --- Walking the entire request list ---
> Sending Access-Reject of id 185 to 127.0.0.1:1025
> Waking up in 4 seconds...
> --- Walking the entire request list ---
> Cleaning up request 0 ID 185 with timestamp 3f68d908
> Nothing to do. Sleeping until we see a request.
> ---------------------------------------------------------------------------
> Later after few seconds in the Client window I got the following
> message
> [EMAIL PROTECTED] root]# radtest bob bob localhost 0 testing123
> Sending Access-Request of id 240 to 127.0.0.1:1812
> User-Name = "bob"
> User-Password = "bob"
> NAS-IP-Address = localhost.localdomain
> NAS-Port = 0
> rad_recv: Access-Reject packet from host 127.0.0.1:1812, id=240,
> length=20
> --------------------------------------------------------------------------
> In FAQ it is given that we should get the following message:
> Ensure that you see the Reply-Message above and that you do NOT see
> an
> "Access denied" message. If you get an Access-Accept message, this
> means that
> the server is running properly.
> ----------------------------------------------------------------------------
> Sir, why am i getting the access-reject message from the server.
> Kindly help me how do i get the access-accept message from the server
> to ensure that the server is running properly?
> in anticipation of reply,
> regards,
> puneeth b.
>
>
> ______________________________________________________________________
> Do you Yahoo!?
> Yahoo! SiteBuilder - Free, easy-to-use web site design software
-
List info/subscribe/unsubscribe? See http://www.freeradius.org/list/users.html
