*Hi Glen,*
*Here we have the end of ve9qrp_700d.wav well I pressed ^C.*
*
*
*BTW: squelch is turned off freedv_set_squelch_en(f2, 0);*
*
*
*state: Rx Sync peak: 1823 sync: 1 SNR: 14.6
triggered: 1 recordany: 0 rxDataCnt 1890 ncodec 14*
*SYN: 2 0 1 0 ; tx_uw 0000000000 rx_uw ; 0000000000*
*SYN: 2 0 1 0 ; tx_uw 0000000000 rx_uw ; 0000000000*
*SYN: 2 0 1 0 ; tx_uw 0000000000 rx_uw ; 0000000000*
*SYN: 2 0 1 0 ; tx_uw 0000000000 rx_uw ; 0000000000*
*SYN: 2 0 1 0 ; tx_uw 0000000000 rx_uw ; 0000000000*
*SYN: 2 0 1 0 ; tx_uw 0000000000 rx_uw ; 0000000000 <- puzzled why no
rx_uw bits here.*
*SYN: 2 0 1 0 ; tx_uw 0000000000 rx_uw ; 0000000000*
*state: Rx Sync peak: 129 sync: 1 SNR: 13.8
triggered: 1 recordany: 0 rxDataCnt 1988 ncodec 14*
*SYN: 2 6 1 0 ; tx_uw 0000000000 rx_uw ; 1101100110*
*SYN: 2 5 1 1 ; tx_uw 0000000000 rx_uw ; 0101010101 <- sync should
drop here.*
*SYN: 2 1 1 2 ; tx_uw 0000000000 rx_uw ; 0010000000*
*SYN: 2 2 1 0 ; tx_uw 0000000000 rx_uw ; 0110000000*
*SYN: 2 1 1 0 ; tx_uw 0000000000 rx_uw ; 0010000000*
*SYN: 2 2 1 0 ; tx_uw 0000000000 rx_uw ; 0000100010*
*SYN: 2 0 1 0 ; tx_uw 0000000000 rx_uw ; 0000000000*
*state: Rx Sync peak: 128 sync: 1 SNR: 1.9
triggered: 1 recordany: 0 rxDataCnt 1988 ncodec 14*
*SYN: 2 0 1 0 ; tx_uw 0000000000 rx_uw ; 0000000000*
*SYN: 2 0 1 0 ; tx_uw 0000000000 rx_uw ; 0000000000*
*SYN: 2 0 1 0 ; tx_uw 0000000000 rx_uw ; 0000000000*
*SYN: 2 2 1 0 ; tx_uw 0000000000 rx_uw ; 0001010000*
*SYN: 2 0 1 0 ; tx_uw 0000000000 rx_uw ; 0000000000*
*SYN: 2 1 1 0 ; tx_uw 0000000000 rx_uw ; 0000000100*
*SYN: 2 0 1 0 ; tx_uw 0000000000 rx_uw ; 0000000000*
A few seconds later I whistle:
*
*
*
state: Rx Sync peak: 130 sync: 1 SNR: 4.2
triggered: 1 recordany: 0 rxDataCnt 1988 ncodec 14
SYN: 2 1 1 0 ; tx_uw 0000000000 rx_uw ; 0100000000
SYN: 2 0 1 0 ; tx_uw 0000000000 rx_uw ; 0000000000
SYN: 2 0 1 0 ; tx_uw 0000000000 rx_uw ; 0000000000
SYN: 2 0 1 0 ; tx_uw 0000000000 rx_uw ; 0000000000
SYN: 2 0 1 0 ; tx_uw 0000000000 rx_uw ; 0000000000
SYN: 2 0 1 0 ; tx_uw 0000000000 rx_uw ; 0000000000
SYN: 2 1 1 0 ; tx_uw 0000000000 rx_uw ; 0000000010
state: Rx Sync peak: 123 sync: 1 SNR: 2.2
triggered: 1 recordany: 0 rxDataCnt 1988 ncodec 14
SYN: 2 0 1 0 ; tx_uw 0000000000 rx_uw ; 0000000000
SYN: 2 0 1 0 ; tx_uw 0000000000 rx_uw ; 0000000000 <- whistle starts
SYN: 2 5 1 0 ; tx_uw 0000000000 rx_uw ; 0110011001
SYN: 2 4 1 1 ; tx_uw 0000000000 rx_uw ; 0011001100
SYN: 2 7 1 2 ; tx_uw 0000000000 rx_uw ; 1101011011
SYN: 2 7 1 3 ; tx_uw 0000000000 rx_uw ; 0101011111
SYN: 2 6 1 4 ; tx_uw 0000000000 rx_uw ; 1011110100
state: Rx Sync peak: 499 sync: 1 SNR: -6.5
triggered: 1 recordany: 0 rxDataCnt 1988 ncodec 14
SYN: 2 7 1 5 ; tx_uw 0000000000 rx_uw ; 1011110101
SYN: 2 5 1 6 ; tx_uw 0000000000 rx_uw ; 0010111010
state: Rx Maybe UnSync peak: 254 sync: 0 SNR: -8.8
triggered: 1 recordany: 0 rxDataCnt 1988 ncodec 0
*
*Alan VK2ZIW*
*
*
*On Wed, 15 Jul 2020 22:45:24 +1000, glen english wrote*
> well, looks OK, looks like it is worked as expected. but...
> It's like the demod freezes. and freezes and doesnt update the UW
buffer......
> and rx_uw[i] is not being updated.
> HMM but
> LINE 1495:
> ofdm->uw_errors+= ofdm->tx_uw[i] ^ rx_uw[i];
> ERRR AHH ofdm->tx_uw[i] IS set to zero (line 242....) and never
updated in that file.
>
> and I cannot find it being updated anywhere else ?
>
> so is it waiting until rx_uw is all zeros, also? maybe , maybe not.
and it waits until rx_uw is non zero ( a whistle) , because the input
level is low (squelched ????) and rx_uw is zero filled.) ?
> can you pls inspect ofdm->tx_uw[i] and rx_uw[i] ? they are
ofdm->nuwbits in length of type uint8.
> you might need to add after the print that you added :
> for(i = 0; i < ofdm->nuwbits; i++) {
> printf("%0u",(unsigned int) ofdm->tx_uw[i]);
> }
> printf("\r\n");
> for(i = 0; i < ofdm->nuwbits; i++) {
> printf("%0u",(unsigned int) ofdm->rx_uw[i]);
> }
> printf("\r\n");
>
> AND OR
>
> the amplitude is super low and the UW word buffer is not getting
flushed with the new noisy frames because the demod goes unlocked.
>
> Do you have plenty of noise going into the demod when the signals
disappear ? what happens if you crank up the level by 10x ?
> NOW.....
>
> (I dont know the demod very well, yet - learning little pieces a bit
at a time)
>
> The UW being 0 in the period following the
>
>
> *state: Rx Sync peak: 106 sync: 1 SNR: 1.2
triggered: 1 recordany: 0 rxDataCnt 1414 ncodec 14*
> *SYN: 2 0 1 0 *
> *SYN: 2 2 1 0 *
> *SYN: 2 0 1 0 *
> *SYN: 2 0 1 0 *
> *SYN: 2 0 1 0 *
> *SYN: 2 1 1 0
> *
>
> On 7/15/2020 9:09 PM, Al Beard wrote:
>
> *Hi Glen,*
> *
> *
> *Done as asked... SYN: sync_state, uw_errors, sync_mode, sync_counter*
> *
> *
>
> *SYN: 2 0 1 0 good solid reception
of ve9qrp_700d.wav*
> *state: Rx Sync peak: 1901 sync: 1 SNR: 15.7
triggered: 1 recordany: 0 rxDataCnt 1218 ncodec 14*
> *SYN: 2 0 1 0 *
> *SYN: 2 0 1 0 *
> *SYN: 2 0 1 0 *
> *SYN: 2 0 1 0 *
> *SYN: 2 0 1 0 *
> * RX txtMsg: cq cq cq hello world*
> * Tx triggered!*
> *SYN: 2 0 1 0 *
>
>
> *
> *
> *......*
> *
> *
>
> *SYN: 2 0 1 0 *
> *SYN: 2 2 1 0 reception of ve9qrp_700d.wav is
over, *
> *SYN: 2 1 1 0 *
> *state: Rx Sync peak: 106 sync: 1 SNR: 1.2
triggered: 1 recordany: 0 rxDataCnt 1414 ncodec 14*
> *SYN: 2 0 1 0 *
> *SYN: 2 2 1 0 *
> *SYN: 2 0 1 0 *
> *SYN: 2 0 1 0 *
> *SYN: 2 0 1 0 *
> *SYN: 2 1 1 0 *
> *SYN: 2 4 1 0 here I whistle into the mic*
> *state: Rx Sync peak: 748 sync: 1 SNR: 3.5
triggered: 1 recordany: 0 rxDataCnt 1428 ncodec 14*
> *SYN: 2 2 1 1 *
> *SYN: 2 1 1 0 *
> *SYN: 2 8 1 0 *
> *SYN: 2 5 1 1 *
> *SYN: 2 6 1 2 *
> *SYN: 2 6 1 3 *
> *SYN: 2 3 1 4 *
> *state: Rx Sync peak: 821 sync: 1 SNR: -4.6
triggered: 1 recordany: 0 rxDataCnt 1428 ncodec 14*
> *SYN: 2 6 1 5 *
> *SYN: 2 3 1 6 *
> *state: Rx Maybe UnSync peak: 110 sync: 0 SNR: -8.4
triggered: 1 recordany: 0 rxDataCnt 1428 ncodec 0*
>
> No more SYN: n n n n messages.
>
>
> *Over to you...*
> *
> *
> *Alan VK2ZIW*
> *
> *
> *
> * *On Wed, 15 Jul 2020 19:43:37 +1000, glen english wrote*
> > Alan, please be sure to keep correct subject line.
> > Right. ofdm.c
> > voidofdm_sync_state_machine(structOFDM *ofdm, uint8_t*rx_uw)
> > there are two synced states, synced (ongoing) and trial sync
(when sync is getting established for the first time- checking if
this is real sync or bogus sync due to frquency offset aliasing)
> >
> > the difference in bits between the unique word template and the
actual received unique word is checked
> > (lines 1494..1496)
> >
> > When synced (ongoing) if the unique_word (uw_errors) error
count is > 2 (IE more than 2 bits different from the template,
ofdm->sync_counter is incremented.
> > when ofdm->sync_counter is >6 AND ofdm->sync_mode== autosync
(line 1540) , sync will be dropped.
> > So, since you can compile from source, I'd like you to insert
some extra debug printfs or whatever and above line 1533,
> > IE immediately before
> > if(ofdm->sync_state== synced) {
> > please print out : (just use %u style, that's fine, do a explicit
cast to unsigned int for each variable in case they are chars )
> > ofdm->sync_state
> > ofdm->uw_errors
> > ofdm->sync_mode
> > ofdm->sync_counter
> > IE
> > printf("SYN: %u %u %u %u \r\n",(unsigned int) ofdm->sync_state,
etc etc
> >
> > just the integer values will be fine, we can look up the numbers.
> > So the sync state machine could do with some refinement, could be
error easily programmer error prone . I will put that on my to-do
list to re write .
> >
> > On 7/15/2020 8:02 AM, Al Beard wrote:
> >
Hi Glen and David,
> >
> > In my testing of "parrot" derived from "freebeacon", mode 700D,
> > I'm "seeing" sync holding up when it shouldn't.
> >
> > I'm running relatively low input levels, similar to what
> >
> >
>
> ---------------------------------------------------
> Alan VK2ZIW
>
> OpenWebMail 2.53, nothing in the cloud.
>
>
>
>
_______________________________________________
Freetel-codec2 mailing
list
Freetel-codec2@lists.sourceforge.net
https://lists.sourceforge.net/lists/listinfo/freetel-codec2
--
Glen
English
RF Communications and Electronics
Engineer
CORTEX
RF
Pacific Media Technologies Pty Ltd trading as Cortex
RF
ABN 40 075 532
008
PO Box 5231 Lyneham ACT 2602,
Australia.
au mobile : +61 (0)418 975077
---------------------------------------------------
Alan VK2ZIW
OpenWebMail 2.53, nothing in the cloud.
_______________________________________________
Freetel-codec2 mailing list
Freetel-codec2@lists.sourceforge.net
https://lists.sourceforge.net/lists/listinfo/freetel-codec2