The file is called $FWDIR/conf/gui-clients -----Original Message----- From: Mailing list for discussion of Firewall-1 [mailto:[EMAIL PROTECTED] On Behalf Of Graham, Chad Sent: Monday, April 26, 2004 12:43 PM To: [EMAIL PROTECTED] Subject: Re: [FW-1] Management Server
Thanks for the quick response, but that client was already added. I was able to connect just fine until I removed the interface. I was under the impression that I would be able to connect to any interface that was defined on the firewall topology page. Is there a file that defines what ip the management console is running on? Since I forgot on my original post: Solaris 2.8 Checkpoint SmartCenter Server NG Feature Pack 3 Build 53938 Thanks Chad Graham [EMAIL PROTECTED] -----Original Message----- From: Mailing list for discussion of Firewall-1 [mailto:[EMAIL PROTECTED] On Behalf Of Robert Plaenk Sent: Monday, April 26, 2004 8:37 AM To: [EMAIL PROTECTED] Subject: Re: [FW-1] Management Server Telnet in and run CPCONFIG, then add a GUI client. Once that is done, you should be able to connect via GUI (on the interface that still works). Once you connect, then you can edit the firewall object, go to interfaces tab and get the interfaces again. -----Original Message----- From: Mailing list for discussion of Firewall-1 [mailto:[EMAIL PROTECTED] On Behalf Of Graham, Chad Sent: Monday, April 26, 2004 10:45 AM To: [EMAIL PROTECTED] Subject: [FW-1] Management Server All, I was trying to fix a problem we were having on one of our firewalls and caused myself a bigger problem. On the firewall topology tab I removed all but the hme0 interface (which the license is bound to) and installed the policy. Well as luck would have it, we used a different interface to connect to the SmatCenter Server and now I cannot get it back. I still have telnet access to the machine so I edited the objects.C file and added the other nic back in, still no luck. I tried SIC reset, still nothing. Always the same error "Connection cannot be initiated. Make sure the server is up and running". This is running on a Solaris machine, and we do not have the GUI license for this machine so I cannot run the GUI on localhost. Is there anything I can do via the command line to allow me to connect to the firewall via the SmartDashboard GUI? Thanks in advance, Chad Graham Email: [EMAIL PROTECTED] <mailto:[EMAIL PROTECTED]> ______________________________________________________________________ This email has been scanned by the MessageLabs Email Security System. For more information please visit http://www.messagelabs.com/email ______________________________________________________________________ ================================================= To set vacation, Out-Of-Office, or away messages, send an email to [EMAIL PROTECTED] in the BODY of the email add: set fw-1-mailinglist nomail ================================================= To unsubscribe from this mailing list, please see the instructions at http://www.checkpoint.com/services/mailing.html ================================================= If you have any questions on how to change your subscription options, email [EMAIL PROTECTED] ================================================= ================================================= To set vacation, Out-Of-Office, or away messages, send an email to [EMAIL PROTECTED] in the BODY of the email add: set fw-1-mailinglist nomail ================================================= To unsubscribe from this mailing list, please see the instructions at http://www.checkpoint.com/services/mailing.html ================================================= If you have any questions on how to change your subscription options, email [EMAIL PROTECTED] ================================================= ______________________________________________________________________ This email has been scanned by the MessageLabs Email Security System. For more information please visit http://www.messagelabs.com/email ______________________________________________________________________ ______________________________________________________________________ This email has been scanned by the MessageLabs Email Security System. For more information please visit http://www.messagelabs.com/email ______________________________________________________________________ ================================================= To set vacation, Out-Of-Office, or away messages, send an email to [EMAIL PROTECTED] in the BODY of the email add: set fw-1-mailinglist nomail ================================================= To unsubscribe from this mailing list, please see the instructions at http://www.checkpoint.com/services/mailing.html ================================================= If you have any questions on how to change your subscription options, email [EMAIL PROTECTED] ================================================= ================================================= To set vacation, Out-Of-Office, or away messages, send an email to [EMAIL PROTECTED] in the BODY of the email add: set fw-1-mailinglist nomail ================================================= To unsubscribe from this mailing list, please see the instructions at http://www.checkpoint.com/services/mailing.html ================================================= If you have any questions on how to change your subscription options, email [EMAIL PROTECTED] =================================================
