not work with versions of IPSO other than 3.5.1, 3.7, 3.7.1, 3.8 and 3.9 This means that these appliances ONLY work with this versions not otherwise
-----Original Message----- From: Mailing list for discussion of Firewall-1 [mailto:[EMAIL PROTECTED] On Behalf Of Wayne Ho Sent: Monday, September 26, 2005 1:12 PM To: [email protected] Subject: Re: [FW-1] IPSO clustering and R55 Thanks. I am considering using IPSO3.8. One inconsistancy I found out from Nokia website is that The nokia article https://support.nokia.com/knowledge/resolutionView.jsp?ResolutionId=23990 mentions "Caution: Nokia IP350 and IP380 appliances can be upgraded to Nokia IPSO 3.9, but they cannot be upgraded or downgraded to IPSO 3.6. These systems do not work with versions of IPSO other than 3.5.1, 3.7, 3.7.1, 3.8 and 3.9." But in the IPSO 3.8.1 release notes, section - Supported Appliance saying IP380 support IPSO3.8.1 ?? Wayne --- Neil Kemp <[EMAIL PROTECTED]> wrote: > We did have problems running 3.7.1 and Load Balancing / Nokia > Clustering. > > There are a number of fixes in 3.8 and above for the above. We made > the changes and most of the issues we had were resolved. > > Thanks. > > On 26/09/05, Dahate, Pramod > <[EMAIL PROTECTED]> wrote: > > > > > > Hi > > Are you using Nokia IP Clustering protocol for > clustering?. If you use > > this protocol in "forwarding mode" than you do not > have to worry about > > the MAC address. Its issue when you use the > multicast mode for > > Clustering when switches give problem. Go through > Nokia > > Clustering_config guide.The config is very simple. > You do not have to > > define any routes. In forwarding mode ,the master > decides which FW will > > process the packet. > > cheers > > > > Pramod Dahate(MCSE,CCNA,CCSA,CISSP) > > Security Analyst > > Network Management Centre > > > > Getronics Australia Pty Limited > > > > -----Original Message----- > > From: Mailing list for discussion of Firewall-1 > > > [mailto:[EMAIL PROTECTED] > On Behalf Of Wayne > > Ho > > Sent: Friday, 23 September 2005 06:09 > > To: [email protected] > > Subject: [FW-1] IPSO clustering and R55 > > > > Dear all: > > > > Did anyone encouter any issue with R55 with IPSO > 3.7.1 clustering > > running on IP380? Is there any other latest > version I should run on > > IP380 meanwhile giving me stability? There is only > limited version of > > IPSO can run on IP380. (No IPSO3.6, 3.7, 3.8...) > Is there anything I > > need to be aware on switching side? > > These 2 FWs will connect to 2 separated 2950. Do I > need to define static > > arp in switch for the virtual MAC? I just wonder > how the switch can > > understand while the FW is load balancing. Do I > also need to define > > default route on each FW to acheive load > balancing/redundency? > > Any input is appreciated. > > > > Many thanks. > > > > Wayne > > > > __________________________________________________ > > Do You Yahoo!? > > Tired of spam? Yahoo! Mail has the best spam > protection around > > http://mail.yahoo.com > > > > ================================================= > > To set vacation, Out-Of-Office, or away messages, > send an email to > > [EMAIL PROTECTED] > > in the BODY of the email add: > > set fw-1-mailinglist nomail > > ================================================= > > To unsubscribe from this mailing list, please see the instructions > > at http://www.checkpoint.com/services/mailing.html > > ================================================= > > If you have any questions on how to change your > subscription options, > > email [EMAIL PROTECTED] > > ================================================= > > > > ================================================= > > To set vacation, Out-Of-Office, or away messages, send an email to > [EMAIL PROTECTED] > > in the BODY of the email add: > > set fw-1-mailinglist nomail > > ================================================= > > To unsubscribe from this mailing list, please see the instructions > > at http://www.checkpoint.com/services/mailing.html > > ================================================= > > If you have any questions on how to change your subscription > > options, email [EMAIL PROTECTED] > > ================================================= > > > > ================================================= > To set vacation, Out-Of-Office, or away messages, send an email to > [EMAIL PROTECTED] > in the BODY of the email add: > set fw-1-mailinglist nomail > ================================================= > To unsubscribe from this mailing list, please see the instructions at > http://www.checkpoint.com/services/mailing.html > ================================================= > If you have any questions on how to change your subscription options, > email [EMAIL PROTECTED] > ================================================= > __________________________________ Yahoo! Mail - PC Magazine Editors' Choice 2005 http://mail.yahoo.com ================================================= To set vacation, Out-Of-Office, or away messages, send an email to [EMAIL PROTECTED] in the BODY of the email add: set fw-1-mailinglist nomail ================================================= To unsubscribe from this mailing list, please see the instructions at http://www.checkpoint.com/services/mailing.html ================================================= If you have any questions on how to change your subscription options, email [EMAIL PROTECTED] ================================================= ================================================= To set vacation, Out-Of-Office, or away messages, send an email to [EMAIL PROTECTED] in the BODY of the email add: set fw-1-mailinglist nomail ================================================= To unsubscribe from this mailing list, please see the instructions at http://www.checkpoint.com/services/mailing.html ================================================= If you have any questions on how to change your subscription options, email [EMAIL PROTECTED] =================================================
