In-line...

On 1/1/2012 4:06 PM, Tom Taylor wrote:


On 01/01/2012 2:58 PM, Joel M. Halpern wrote:
Thank you for responding promptly Tom. Let me try to elaborate on the
two issues where I was unclear.

On the ingress-egress-aggregate issue and ECMP, the concern I have is
relative to the third operational alternative where routing is used to
determine where the ingress and egress of a flow is. To be blunt, as far
as I can tell this does not work.
1) It does not work on the ingress side because traffic from a given
source prefix can come in at multiple places. Some of these places may
claim reachability to the source prefix. Some may not. While a given
flow will use only one of these paths, there is no way to determine from
routing information, at the egress, which ingress that flow used.
2) A site may use multiple exits for a given destination prefix. Again,
while the site will only use one of these egresses for a given flow,
there is no way for the ingress to know which egress it will be on the
basis of routing information.
Thus, the text seems to allow for a behavior that simply does not work.

[PTT] I think the disconnect here is that you read the text to say that
an individual node uses routing information to determine the IEA. That
wasn't the intention. Instead, administrators use routing information to
derive filters that are installed at the ingress and egress nodes.

As far as I can tell, your response describes a situation even less effective than what I assumed. Firstly, it does not matter whether it is the edge node, the decision node, or the human administrator. Routing information is not enough to determine what the ingress-egress pairing is. The problems I describe above apply no matter who is making the decision. Secondly, having a human make the decision means that as soon as routing changes, the configured filters are wrong.

I would suggest that the text in question be removed, and replaced with a warning against attempting what is currently described.


I am still confused about the relationship of section 3.3.2 to the
behavior you describe. 3.3.2 says that as long as any excess traffic is
being reported, teh decision point shall direct the blocking of
additional flows. That does not match 3.3.1, and does not match your
description.

[PTT] I can't see the text in section 3.3.2 that says you continue to
block as long as any excess traffic is being reported. What I think it
says is that as long as excess traffic is reported, the decision point
checks to see whether the traffic being admitted to the aggregate
exceeds the supportable level. Excess traffic may be non-zero, yet no
termination may be required (i.e., traffic is below the second threshold).

I think I see what you are saying. If I am reading this correctly, the decision process must re-calculate to determine if there is termination every time it receives a report with non-zero excess and the port is already blocked. But it does not have to actually block anything. This however seems to depend upon the correct relative configuration of the limit that flips it into blocked state, the value of U, and maybe some other values. Put differently, I understand that the two are not contradictory. However, since the two things use different calculations, it is not at all clear that they are consistent. This may well be acceptable. But the difference in methods is likely to lead to confusion. So, as a minor (rather than major) comment, I would suggest that you provide clarifying text explaining why it is okay to use one condition to decide if there is blocking, but a different condition (which could produce a lower threshold) to decide how much to get rid of.

Yours,
Joel


Yours,
Joel

On 1/1/2012 2:48 PM, Tom Taylor wrote:
Thanks for the review, Joel. Comments below, marked with [PTT].

On 31/12/2011 4:50 PM, Joel M. Halpern wrote:
I am the assigned Gen-ART reviewer for this draft. For background on
Gen-ART, please see the FAQ at
<http://wiki.tools.ietf.org/area/gen/trac/wiki/GenArtfaq>.

Please resolve these comments along with any other Last Call comments
you may receive.

Document: draft-ietf-pcn-sm-edge-behaviour-08
PCN Boundary Node Behaviour for the Single Marking (SM) Mode of
Operation
Reviewer: Joel M. Halpern
Review Date: 31-Dec-2011
IETF LC End Date: 13-Jan-2012
IESG Telechat date: N/A

Summary: This documents is almost ready for publication as an
Informational RFC.

Question: Given that the document defines a complex set of behaviors,
which are mandatory for compliant systems, it seems that this ought to
be Experimental rather than Informational. It describes something that
could, in theory, later become standards track.

[PTT] OK, we've wobbled on this one, but we can follow your suggestion.

Major issues:
Section 2 on Assumed Core Network Behavior for SM, in the third bullet,
states that the PCN-domain satisfies the conditions specified in RFC
5696. Unfortunately, look at RFC 5696 I can not tell what conditions
these are. Is this supposed to be a reference to RFC 5559 instead? No
matter which document it is referencing, please be more specific about
which section / conditions are meant.

[PTT] You are right that RFC 5696 isn't relevant. It's such a long time
since that text was written that I can't recall what the intention was.
My inclination at the moment is simply to delete the bullet.

It would have been helpful if the early part of the document indicated
that the edge node information about how to determine
ingress-egress-aggregates was described in section 5.
In conjunction with that, section 5.1.2, third paragraph, seems to
describe an option which does not seem to quite work. After describing
how to use tunneling, and how to work with signaling, the text
refers to
inferring the ingress-egress-aggregate from the routing information. In
the presence of multiple equal-cost domain exits (which does occur in
reality), the routing table is not sufficient information to make this
determination. Unless I am very confused (which does happen) this seems
to be a serious hole in the specification.

[PTT] I'm not sure what the issue is here. As I understand it, operators
don't assign packets randomly to a given path in the presence of
alternatives -- they choose one based on values in the packet header.
The basic intent is that packets of a given microflow all follow the
same path, to prevent unnecessary reordering and minimize jitter. The
implication is that filters can be defined at the ingress nodes to
identify the packets in a given ingress-egress-aggregate (i.e. flowing
from a specific ingress node to a specific egress node) based on their
header contents. The filters to do the same job at egress nodes are a
different problem, but they are not affected by ECMP.

Minor issues:
Section 3.3.1 states that the "block" decision occurs when the CLE
(excess over total) rate exceeds the configured limit. However, section
3.3.2 states that the decision node must take further stapes if the
excess rate is non-zero in further reports. Is this inconsistency
deliberate? If so, please explain. If not, please fix. (If it is
important to drive the excess rate to 0, then why is action only
initiated when the ratio is above a configured value, rather than any
non-zero value? I can conceive of various reasons. But none are
stated.)

[PTT] We aren't driving the excess rate to zero, but to a value equal to
something less than (U - 1)/U. (The "something less" is because of
packet dropping at interior nodes.) The assumption is that (U - 1)/U is
greater than CLE-limit. Conceptually, PCN uses two thresholds. When the
CLE is below the first threshold, new flows are admitted. Above that
threshold, they are blocked. When the CLE is above the second threshold,
flows are terminated to bring them down to that threshold. In the SM
mode of operation, the first threshold is specified directly on a
per-link basis by the value CLE-limit. The second threshold is specified
by the same value (U - 1)/U for all links. With the CL mode of operation
the second threshold is also specified directly for each link.


Nits/editorial comments:






_______________________________________________
Gen-art mailing list
[email protected]
https://www.ietf.org/mailman/listinfo/gen-art

Reply via email to