What should happen when you have several tables? Thanks,
-- Raul On Thu, Aug 28, 2014 at 4:23 PM, Thomas Costigliola <[email protected]> wrote: > My use case is that I click a cell on the table, then click a button that > will have some effect that depends on what cell in the table is > highlighted. I suppose I can save the selection to a state variable in the > table click event and use it in subsequent events. But this would logically > lead me to consider that the table state should be what I saved. Unless > there are use cases where having a table state in another event would cause > some disruption or confusion. > > As a slight aside, I have been wanting to get and set the selection of a > table with wd commands, is that something you have thought about > supporting? For example an option to wd'set table block...', that actually > highlights the cells as if they were selected with the mouse and a > corresponding get command to get the selection that was last highlighted. > > > On Thu, Aug 28, 2014 at 4:05 PM, chris burke <[email protected]> wrote: > > > This was done originally because there is no obvious state that a table > has > > when a non-table event occurs, unlike say a checkbox which is either on > or > > off. What information there is can be captured when a table event occurs. > > > > However, we are open to suggestions on this, and it is easy to change. > > > > > > On Thu, Aug 28, 2014 at 12:24 PM, Thomas Costigliola <[email protected] > > > > wrote: > > > > > If a table control is not the last control clicked it doesn't show up > in > > > form data. > > > > > > > > > wd 0 : 0 > > > > > > pc f closeok; > > > > > > bin v; > > > > > > cc b button;cn button; > > > > > > cc t table 2 2; > > > > > > set t data A B C D; > > > > > > bin z; > > > > > > pshow; > > > > > > ) > > > > > > > > > If I click the button then: > > > > > > > > > wd'qd' > > > > > > ┌────────────┬────────┐ > > > > > > │syslocalep │Special │ > > > > > > ├────────────┼────────┤ > > > > > > │syshwndp │89319136│ > > > > > > ├────────────┼────────┤ > > > > > > │syshwndc │89605104│ > > > > > > ├────────────┼────────┤ > > > > > > │syslastfocus│ │ > > > > > > ├────────────┼────────┤ > > > > > > │sysmodifiers│0 │ > > > > > > ├────────────┼────────┤ > > > > > > │sysdata │ │ > > > > > > └────────────┴────────┘ > > > > > > > > > But when I click in the table then: > > > > > > > > > wd'qd' > > > > > > ┌────────────┬────────┐ > > > > > > │syslocalep │Special │ > > > > > > ├────────────┼────────┤ > > > > > > │syshwndp │89319136│ > > > > > > ├────────────┼────────┤ > > > > > > │syshwndc │89605104│ > > > > > > ├────────────┼────────┤ > > > > > > │syslastfocus│ │ > > > > > > ├────────────┼────────┤ > > > > > > │sysmodifiers│0 │ > > > > > > ├────────────┼────────┤ > > > > > > │sysdata │ │ > > > > > > ├────────────┼────────┤ > > > > > > │t │0 1 │ > > > > > > ├────────────┼────────┤ > > > > > > │t_select │0 0 1 1 │ > > > > > > └────────────┴────────┘ > > > > > > > > > And clicking the button again: > > > > > > > > > wd'qd' > > > > > > ┌────────────┬────────┐ > > > > > > │syslocalep │Special │ > > > > > > ├────────────┼────────┤ > > > > > > │syshwndp │89319136│ > > > > > > ├────────────┼────────┤ > > > > > > │syshwndc │89605104│ > > > > > > ├────────────┼────────┤ > > > > > > │syslastfocus│ │ > > > > > > ├────────────┼────────┤ > > > > > > │sysmodifiers│0 │ > > > > > > ├────────────┼────────┤ > > > > > > │sysdata │ │ > > > > > > └────────────┴────────┘ > > > > > > > > > This goes for event data too. I need to process the table from another > > > control's event. Is there any way to do this? > > > ---------------------------------------------------------------------- > > > For information about J forums see http://www.jsoftware.com/forums.htm > > ---------------------------------------------------------------------- > > For information about J forums see http://www.jsoftware.com/forums.htm > ---------------------------------------------------------------------- > For information about J forums see http://www.jsoftware.com/forums.htm > ---------------------------------------------------------------------- For information about J forums see http://www.jsoftware.com/forums.htm
