On Thu, Apr 16, 2009 at 3:20 PM, Hal Rosenstock <[email protected]> wrote: > On Thu, Apr 16, 2009 at 3:18 PM, Yicheng Jia <[email protected]> wrote: >> >> They both are POLLING before "reset". > > Then they _should_ come back to INIT. > > What does the local LDDS value say after reset ? Any way to get the > switch port LDDS value ?
Are you resetting the switch from the peer HCA port or some other port ? That's what Nicolas asked but I might have missed the answer. Also, try disable (wait) and then enable and see if that works. If I recall correctly, you had those links which are taking a long time to initialize. If the link stays down forever after disable, this won't work but I want to be sure. -- Hal > -- Hal > >> Thanks! >> Yicheng Jia >> >> >> >> >> Hal Rosenstock <[email protected]> >> >> 04/16/2009 01:53 PM >> >> To >> Yicheng Jia <[email protected]> >> cc >> Nicolas Morey-Chaisemartin <[email protected]>, >> [email protected] >> Subject >> Re: [ofa-general] link width problem of Qlogic 9024 unmanaged switch >> >> >> >> >> On Thu, Apr 16, 2009 at 11:12 AM, Yicheng Jia <[email protected]> wrote: >>> >>> Hi Nicolas, >>> >>> After this "reset" command, both ports are DOWN forever, I can only get >>> portinfo from local port. >>> >>> I am sure that the port that has been reset is not the local port, >>> otherwise >>> it will prompt "node type not switch" error. >>> >>> I tried to enable this switch port from another port and brought it to >>> POLLING state, but as long as I use "reset", both ports are DOWN. >> >> What are the peer port's LinkDownDefaultStates ? Sounds like one or >> more must be Sleeping rather than Polling for some reason. >> >> -- Hal >> >>> Thanks! >>> >>> Yicheng Jia >>> >>> >>> >>> >>> Nicolas Morey-Chaisemartin <[email protected]> >>> >>> 04/16/2009 12:43 AM >>> >>> To >>> Yicheng Jia <[email protected]> >>> cc >>> [email protected] >>> Subject >>> Re: [ofa-general] link width problem of Qlogic 9024 unmanaged switch >>> >>> >>> >>> >>> By any chances have you not reset the port you're on? >>> Have you tried using another node to enable the port again? >>> >>> Nicolas >>> >>> Le 16/04/2009 00:45, Yicheng Jia a écrit : >>>> >>>> Hello Randy, >>>> >>>> I am trying to run "ibportstate reset" to reset the switch port on the >>>> other side in order to get 4x link. However I get the following error: >>>> ibwarn: [19660] mad_rpc: _do_madrpc failed; dport (Lid 7) >>>> ibportstate: iberror: failed: smp set portinfo failed >>>> >>>> And the port status change to DOWN after this. Have you ever tried to >>>> run "ibportstate" to reset the switch port? >>>> >>>> Thanks! >>>> >>>> Yicheng Jia >>>> >>>> >>>> >>>> >>>> >>>> ------------------------------ >>>> >>>> Message: 2 >>>> Date: Wed, 4 Mar 2009 18:39:54 -0600 >>>> From: Randy Halverson <[email protected]> >>>> Subject: [ofa-general] link width problem of Qlogic 9024 unmanaged >>>> switch >>>> To: "'[email protected]'" <[email protected]> >>>> Message-ID: >>>> <[email protected]> >>>> Content-Type: text/plain; charset="us-ascii" >>>> >>>> Hello Yicheng, >>>> >>>> After checking internally, this appears to be a known problem with older >>>> firmware for the 9024FC switches. >>>> >>>> It appears that you or another person at 'tmriusa.com' has recently >>>> opened a case with QLogic Tech Support for this issue. Please continue >>>> to work with QLogic Tech Support on firmware upgrade resolution since >>>> you probably don't have our FastFabric Tools to manage the 9024FC >>>> switches.. >>>> >>>> Regards, >>>> >>>> Randy >>>> Technical Support >>>> QLogic Corporation >>>> -------------- next part -------------- >>>> >>>> >>>> >>>> >>>> _____________________________________________________________________________ >>>> Scanned by IBM Email Security Management Services powered by >>>> MessageLabs. For more information please visit http://www.ers.ibm.com >>>> >>>> >>>> _____________________________________________________________________________ >>>> <http://www.ers.ibm.com/> >>>> >>>> >>>> >>>> _____________________________________________________________________________ >>>> Scanned by IBM Email Security Management Services powered by >>>> MessageLabs. For more information please visit http://www.ers.ibm.com >>>> >>>> >>>> _____________________________________________________________________________ >>>> >>>> >>>> ------------------------------------------------------------------------ >>>> >>>> _______________________________________________ >>>> general mailing list >>>> [email protected] >>>> http://lists.openfabrics.org/cgi-bin/mailman/listinfo/general >>>> >>>> To unsubscribe, please visit >>>> http://openib.org/mailman/listinfo/openib-general >>> >>> >>> >>> _____________________________________________________________________________ >>> Scanned by IBM Email Security Management Services powered by MessageLabs. >>> For more information please visit http://www.ers.ibm.com >>> >>> _____________________________________________________________________________ >>> >>> >>> >>> _____________________________________________________________________________ >>> Scanned by IBM Email Security Management Services powered by MessageLabs. >>> For more information please visit http://www.ers.ibm.com >>> >>> _____________________________________________________________________________ >>> >>> _______________________________________________ >>> general mailing list >>> [email protected] >>> http://lists.openfabrics.org/cgi-bin/mailman/listinfo/general >>> >>> To unsubscribe, please visit >>> http://openib.org/mailman/listinfo/openib-general >>> >> >> _____________________________________________________________________________ >> Scanned by IBM Email Security Management Services powered by MessageLabs. >> For more information please visit http://www.ers.ibm.com >> _____________________________________________________________________________ >> >> >> _____________________________________________________________________________ >> Scanned by IBM Email Security Management Services powered by MessageLabs. >> For more information please visit http://www.ers.ibm.com >> _____________________________________________________________________________ >> > _______________________________________________ general mailing list [email protected] http://lists.openfabrics.org/cgi-bin/mailman/listinfo/general To unsubscribe, please visit http://openib.org/mailman/listinfo/openib-general
