I run tail -f /var/log/messages via ssh to my quake3 server box to see what is goin on.
Today after I finished installing Gentoo, I noticed these errors popping up.
<----snip----->
Dec 6 02:22:44 quake3server hda: dma_intr: error=0x84 { DriveStatusError BadCRC }
Dec 6 02:27:06 quake3server hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
Dec 6 02:27:06 quake3server hda: dma_intr: error=0x84 { DriveStatusError BadCRC }
Dec 6 02:09:27 quake3server hda: dma_intr: error=0x84 { DriveStatusError BadCRC }
Dec 6 02:09:27 quake3server hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
Dec 6 02:09:27 quake3server hda: dma_intr: error=0x84 { DriveStatusError BadCRC }
<----snip----->
Can anyone tell me what could be causing this and how to get rid of it.. It did not happen when I used SuSE 8.2 and Slackware 9.1 on the same box, with the same hardware. My Gentoo system is the following:
Linux version 2.6.0-test11-gentoo-r1 ([EMAIL PROTECTED]) (gcc version 3.2.3 20030422 (Gentoo Linux 1.4 3.2.3-r3, propolice)) #1 Fri Dec 5 13:42:05 CST 2003
Could it be the kernel? I thought I had all the hard drive / dma stuff compiled into the kernel as I always do.
Also I am using reiserfs
Here is the output of lspci -v:
00:00.0 Host bridge: Advanced Micro Devices [AMD] AMD-751 [Irongate] System Controller (rev 25) Flags: bus master, medium devsel, latency 32 Memory at e0000000 (32-bit, prefetchable) [size=128M] Memory at efdff000 (32-bit, prefetchable) [size=4K] I/O ports at d400 [disabled] [size=4] Capabilities: [a0] AGP version 1.0
00:01.0 PCI bridge: Advanced Micro Devices [AMD] AMD-751 [Irongate] AGP Bridge (rev
01) (prog-if 00 [Normal decode])
Flags: bus master, 66Mhz, medium devsel, latency 32
Bus: primary=00, secondary=01, subordinate=01, sec-latency=32
I/O behind bridge: 00009000-00009fff
Memory behind bridge: efe00000-efefffff
Prefetchable memory behind bridge: d7c00000-d7cfffff00:03.0 VGA compatible controller: ATI Technologies Inc Rage 128 Pro Ultra TR (prog-if
00 [VGA])
Subsystem: ATI Technologies Inc: Unknown device 0009
Flags: bus master, stepping, medium devsel, latency 32, IRQ 11
Memory at e8000000 (32-bit, prefetchable) [size=64M]
I/O ports at d800 [size=256]
Memory at efffc000 (32-bit, non-prefetchable) [size=16K]
Expansion ROM at effc0000 [disabled] [size=128K]
Capabilities: [5c] Power Management version 200:07.0 ISA bridge: VIA Technologies, Inc. VT82C686 [Apollo Super South] (rev 1b)
Subsystem: VIA Technologies, Inc. VT82C686/A PCI to ISA Bridge
Flags: bus master, stepping, medium devsel, latency 000:07.1 IDE interface: VIA Technologies, Inc.
VT82C586A/B/VT82C686/A/B/VT8233/A/C/VT8235 PIPC Bus Master IDE (rev 06) (prog-if 8a
[Master SecP PriP])
Flags: bus master, medium devsel, latency 32
I/O ports at ffa0 [size=16]
Capabilities: [c0] Power Management version 200:07.2 USB Controller: VIA Technologies, Inc. USB (rev 0e) (prog-if 00 [UHCI])
Subsystem: VIA Technologies, Inc. (Wrong ID) USB Controller
Flags: bus master, medium devsel, latency 32, IRQ 11
I/O ports at cc00 [size=32]
Capabilities: [80] Power Management version 200:07.3 USB Controller: VIA Technologies, Inc. USB (rev 0e) (prog-if 00 [UHCI])
Subsystem: VIA Technologies, Inc. (Wrong ID) USB Controller
Flags: bus master, medium devsel, latency 32, IRQ 11
I/O ports at d000 [size=32]
Capabilities: [80] Power Management version 200:07.4 SMBus: VIA Technologies, Inc. VT82C686 [Apollo Super ACPI] (rev 20)
Flags: medium devsel00:09.0 Ethernet controller: Linksys Network Everywhere Fast Ethernet 10/100 model
NC100 (rev 11)
Subsystem: Linksys: Unknown device 0574
Flags: bus master, medium devsel, latency 32, IRQ 10
I/O ports at c800 [size=256]
Memory at efffbc00 (32-bit, non-prefetchable) [size=1K]
Expansion ROM at effa0000 [disabled] [size=128K]
Capabilities: [c0] Power Management version 2Thanks
TriKster Abacus irc.freenode.net #cllug #gentoo #linuxfriends irc.cotse.com #linux http://www.cllug.org http://www.trikster.homelinux.org icq# 266645328
-- [EMAIL PROTECTED] mailing list
