So this is for my motherboard's (Nehalem - so only one generation before
yours) onboard Intel Host Controller... Only a SATA-2 3Gbit capable device.
00:1f.2 SATA controller: Intel Corporation 82801JI (ICH10 Family) SATA AHCI
Controller (prog-if 01 [AHCI 1.0])
Subsystem: ASUSTeK Computer Inc. P5Q Deluxe Motherboard
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 27
Region 0: I/O ports at 8c00 [size=8]
Region 1: I/O ports at 8880 [size=4]
Region 2: I/O ports at 8800 [size=8]
Region 3: I/O ports at 8480 [size=4]
Region 4: I/O ports at 8400 [size=32]
Region 5: Memory at f7efc000 (32-bit, non-prefetchable) [size=2K]
Capabilities: [80] MSI: Enable+ Count=1/16 Maskable- 64bit-
Address: fee00000 Data: 4082
Capabilities: [70] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot+,D3cold-)
Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [a8] SATA HBA v1.0 BAR4 Offset=00000004
Capabilities: [b0] PCI Advanced Features
AFCap: TP+ FLR+
AFCtrl: FLR-
AFStatus: TP-
Kernel driver in use: ahci
uname -r
3.19.0-gentoo
For my Samsung 830 / 850 Pro SSDs I don't see any similar NCQ queuing
error(s) in my boot logs (they are hooked up to the Intel Controller just
now - since I can't connect them to my 6Gbit LSI Controller - arrrggg!!)
Perhaps this issue is confined to the Samsung EVO lines?
On 25 February 2015 at 15:02, Stefan G. Weichinger <[email protected]> wrote:
> On 25.02.2015 14:18, Bob Wya wrote:
>
> > Just out of interest what make is the Host Controller on your
> > motherboard... Is it a Intel one? Or some crappy addon chipset? Perhaps
> you
> > could post the output of lscpi (with lots of -vvvv flags - just the Host
> > Controller bit)?
>
>
> 00:1f.2 SATA controller: Intel Corporation 6 Series/C200 Series Chipset
> Family SATA AHCI Controller (rev 05) (prog-if 01 [AHCI 1.0])
> Subsystem: Hewlett-Packard Company 6 Series/C200 Series Chipset
> Family
> SATA AHCI Controller
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
> Stepping- SERR- FastB2B- DisINTx+
> Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
> <TAbort- <MAbort- >SERR- <PERR- INTx-
> Latency: 0
> Interrupt: pin B routed to IRQ 26
> Region 0: I/O ports at f070 [size=8]
> Region 1: I/O ports at f060 [size=4]
> Region 2: I/O ports at f050 [size=8]
> Region 3: I/O ports at f040 [size=4]
> Region 4: I/O ports at f020 [size=32]
> Region 5: Memory at fb205000 (32-bit, non-prefetchable) [size=2K]
> Capabilities: [80] MSI: Enable+ Count=1/1 Maskable- 64bit-
> Address: feeff00c Data: 41d1
> Capabilities: [70] Power Management version 3
> Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
> PME(D0-,D1-,D2-,D3hot+,D3cold-)
> Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
> Capabilities: [a8] SATA HBA v1.0 BAR4 Offset=00000004
> Capabilities: [b0] PCI Advanced Features
> AFCap: TP+ FLR+
> AFCtrl: FLR-
> AFStatus: TP-
> Kernel driver in use: ahci
>
>
>
>
>
--
All the best,
Robert
