Hi,
I have a question about this one. I noticed a good while back that when
I try to save a image with Seamonkey, it takes a lot longer than it used
too. I save them this way, right click on the image then click save
image as and in the pop up I click save. After hitting the save button,
it takes several seconds, 5 or so, to save a image to disk. I always
make sure the image is completely loaded since I am on dial-up. It used
to do this really fast and I'm not sure what could be causing this. It
also makes my CPU go to about 80% or so.
This is some info about my system. AMD 2500+ with 1Gb of ram. I have a
two IDE UDMA drives on this rig. More info:
> [EMAIL PROTECTED] / # hdparm -i /dev/hda
>
> /dev/hda:
>
> Model=Maxtor 6Y080P0, FwRev=YAR41BW0, SerialNo=Y22J9KXE
> Config={ Fixed }
> RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=57
> BuffType=DualPortCache, BuffSize=7936kB, MaxMultSect=16, MultSect=16
> CurCHS=4047/16/255, CurSects=16511760, LBA=yes, LBAsects=160086528
> IORDY=on/off, tPIO={min:120,w/IORDY:120}, tDMA={min:120,rec:120}
> PIO modes: pio0 pio1 pio2 pio3 pio4
> DMA modes: mdma0 mdma1 mdma2
> UDMA modes: udma0 udma1 udma2 udma3 udma4 udma5 *udma6
> AdvancedPM=yes: disabled (255) WriteCache=enabled
> Drive conforms to: ATA/ATAPI-7 T13 1532D revision 0:
> ATA/ATAPI-1,2,3,4,5,6,7
>
> * signifies the current active mode
>
> [EMAIL PROTECTED] / #
> [EMAIL PROTECTED] / # hdparm -i /dev/hdb
>
> /dev/hdb:
>
> Model=WDC WD800BB-00DKA0, FwRev=77.07W77, SerialNo=WD-WCAHL2497094
> Config={ HardSect NotMFM HdSw>15uSec SpinMotCtl Fixed DTR>5Mbs
> FmtGapReq }
> RawCHS=16383/16/63, TrkSize=57600, SectSize=600, ECCbytes=74
> BuffType=DualPortCache, BuffSize=2048kB, MaxMultSect=16, MultSect=16
> CurCHS=16383/16/63, CurSects=16514064, LBA=yes, LBAsects=156301488
> IORDY=on/off, tPIO={min:120,w/IORDY:120}, tDMA={min:120,rec:120}
> PIO modes: pio0 pio1 pio2 pio3 pio4
> DMA modes: mdma0 mdma1 mdma2
> UDMA modes: udma0 udma1 udma2 udma3 udma4 *udma5
> AdvancedPM=no WriteCache=enabled
> Drive conforms to: Unspecified: ATA/ATAPI-1,2,3,4,5,6
>
> * signifies the current active mode
>
> [EMAIL PROTECTED] / #
> [EMAIL PROTECTED] / # hdparm -tT /dev/hda
>
> /dev/hda:
> Timing cached reads: 834 MB in 2.00 seconds = 416.40 MB/sec
> Timing buffered disk reads: 156 MB in 3.02 seconds = 51.69 MB/sec
> [EMAIL PROTECTED] / #
> [EMAIL PROTECTED] / # hdparm -tT /dev/hdb
>
> /dev/hdb:
> Timing cached reads: 814 MB in 2.00 seconds = 406.93 MB/sec
> Timing buffered disk reads: 126 MB in 3.03 seconds = 41.55 MB/sec
> [EMAIL PROTECTED] / #
> [EMAIL PROTECTED] / # equery list seamonkey
> [ Searching for package 'seamonkey' in all categories among: ]
> * installed packages
> [I--] [ ] www-client/seamonkey-1.1.2 (0)
> [EMAIL PROTECTED] / #
Open to ideas because this is annoying as heck. Images size doesn't
seem to matter either. Big or large, it takes longer.
Thanks much.
Dale
:-) :-)
