Hi there,
this thing is a wireless-usb-key and it apparently comes in 3 versions; the
1st and the 3rd have linux drivers (3rd is RTL8187) while the 2nd requires
ndiswrapper.
Well, I have tried pretty much everything here and the best results I get are
with ndiswrapper (I just get a little more info). When I just do a ndiswrapper
-l, it gives:
net8187b : driver installed
Which is good, if I plug the device and try that again, I get:
net8187b : driver installed
device (0BDA:8189) present
And /var/log/messages shows only those two lines:
usb 1-2: new full speed USB device using uhci_hcd and address 3
sb 1-2: configuration #1 chosen from 1 choice
After which, in ifconfig -a, I still only have my two eth{0,1} and lo.
My goal is to get the interface, after that, I'll be good to go, but this here
is really bugging me. I'm including attachments containing my dmesg, lsusb -v,
and lspci -v (just in case).
Thanks in advance for any help!
Simon
Linux version 2.6.24 ([EMAIL PROTECTED]) (gcc version 4.1.2 (Gentoo 4.1.2
p1.1)) #7 SMP Fri Aug 29 10:32:22 EDT 2008
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 00000000000a0000 (usable)
BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000001fff0000 (usable)
BIOS-e820: 000000001fff0000 - 000000001fff3000 (ACPI NVS)
BIOS-e820: 000000001fff3000 - 0000000020000000 (ACPI data)
BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved)
0MB HIGHMEM available.
511MB LOWMEM available.
Entering add_active_range(0, 0, 131056) 0 entries of 256 used
Zone PFN ranges:
DMA 0 -> 4096
Normal 4096 -> 131056
HighMem 131056 -> 131056
Movable zone start PFN for each node
early_node_map[1] active PFN ranges
0: 0 -> 131056
On node 0 totalpages: 131056
DMA zone: 32 pages used for memmap
DMA zone: 0 pages reserved
DMA zone: 4064 pages, LIFO batch:0
Normal zone: 991 pages used for memmap
Normal zone: 125969 pages, LIFO batch:31
HighMem zone: 0 pages used for memmap
Movable zone: 0 pages used for memmap
DMI 2.1 present.
ACPI: RSDP 000F71A0, 0014 (r0 FIC )
ACPI: RSDT 1FFF3000, 0028 (r1 FIC KA6110 30302E31 AWRD 0)
ACPI: FACP 1FFF3040, 0074 (r1 FIC KA6110 30302E31 AWRD 0)
ACPI: DSDT 1FFF30C0, 2216 (r1 FIC KA6110 1000 MSFT 1000009)
ACPI: FACS 1FFF0000, 0040
ACPI: BIOS age (1999) fails cutoff (2001), acpi=force is required to enable ACPI
ACPI: Disabling ACPI support
Allocating PCI resources starting at 30000000 (gap: 20000000:dfff0000)
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 130033
Kernel command line: root=/dev/hdb1 hdc=ide-scsi
ide_setup: hdc=ide-scsi
Local APIC disabled by BIOS -- you can enable it with "lapic"
mapped APIC to ffffb000 (0140c000)
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Initializing CPU#0
PID hash table entries: 2048 (order: 11, 8192 bytes)
Detected 451.049 MHz processor.
Console: colour VGA+ 80x25
console [tty0] enabled
Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
Memory: 512928k/524224k available (3413k kernel code, 10788k reserved, 1747k
data, 284k init, 0k highmem)
virtual kernel memory layout:
fixmap : 0xffe15000 - 0xfffff000 (1960 kB)
pkmap : 0xff800000 - 0xffc00000 (4096 kB)
vmalloc : 0xe0800000 - 0xff7fe000 ( 495 MB)
lowmem : 0xc0000000 - 0xdfff0000 ( 511 MB)
.init : 0xc0613000 - 0xc065a000 ( 284 kB)
.data : 0xc045556e - 0xc060a334 (1747 kB)
.text : 0xc0100000 - 0xc045556e (3413 kB)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
SLUB: Genslabs=11, HWalign=32, Order=0-1, MinObjects=4, CPUs=1, Nodes=1
Calibrating delay using timer specific routine.. 903.30 BogoMIPS (lpj=1806616)
Mount-cache hash table entries: 512
CPU: After generic identify, caps: 0387f9ff 00000000 00000000 00000000 00000000
00000000 00000000 00000000
CPU: L1 I cache: 16K, L1 D cache: 16K
CPU: L2 cache: 512K
CPU serial number disabled.
CPU: After all inits, caps: 0383f9ff 00000000 00000000 00000040 00000000
00000000 00000000 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
Compat vDSO mapped to ffffe000.
Checking 'hlt' instruction... OK.
SMP alternatives: switching to UP code
Freeing SMP alternatives: 18k freed
CPU0: Intel Pentium III (Katmai) stepping 03
SMP motherboard not detected.
Local APIC not detected. Using dummy APIC emulation.
Brought up 1 CPUs
net_namespace: 64 bytes
xor: automatically using best checksumming function: pIII_sse
pIII_sse : 924.000 MB/sec
xor: using function: pIII_sse (924.000 MB/sec)
NET: Registered protocol family 16
PCI: PCI BIOS revision 2.10 entry at 0xfb3e0, last bus=1
PCI: Using configuration type 1
Setting up standard PCI resources
ACPI: Interpreter disabled.
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI: disabled
SCSI subsystem initialized
libata version 3.00 loaded.
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
PCI: Probing PCI hardware
PCI: Probing PCI hardware (bus 00)
PCI: Using IRQ router VIA [1106/0596] at 0000:00:07.0
PCI: Bridge: 0000:00:01.0
IO window: c000-cfff
MEM window: e8000000-e9ffffff
PREFETCH window: e0000000-e7ffffff
PCI: Setting latency timer of device 0000:00:01.0 to 64
NET: Registered protocol family 2
Time: tsc clocksource has been installed.
IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
TCP established hash table entries: 16384 (order: 5, 131072 bytes)
TCP bind hash table entries: 16384 (order: 5, 131072 bytes)
TCP: Hash tables configured (established 16384 bind 16384)
TCP reno registered
Machine check exception polling timer started.
cpufreq: No nForce2 chipset.
IA-32 Microcode Update Driver: v1.14a <[EMAIL PROTECTED]>
Total HugeTLB memory allocated, 0
Installing knfsd (copyright (C) 1996 [EMAIL PROTECTED]).
fuse init (API version 7.9)
async_tx: api initialized (sync-only)
io scheduler noop registered
io scheduler anticipatory registered (default)
io scheduler deadline registered
io scheduler cfq registered
PCI: VIA PCI bridge detected. Disabling DAC.
Activating ISA DMA hang workarounds.
Boot video device is 0000:01:00.0
Real Time Clock Driver v1.12ac
Linux agpgart interface v0.102
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
loop: module loaded
Intel(R) PRO/1000 Network Driver - version 7.3.20-k2
Copyright (c) 1999-2006 Intel Corporation.
ne2k-pci.c:v1.03 9/22/2003 D. Becker/P. Gortmaker
PCI: setting IRQ 5 as level-triggered
PCI: Found IRQ 5 for device 0000:00:0b.0
eth0: RealTek RTL-8029 found at 0xe000, IRQ 5, 00:00:b4:a4:c5:e7.
PCI: setting IRQ 11 as level-triggered
PCI: Found IRQ 11 for device 0000:00:0c.0
eth1: RealTek RTL-8029 found at 0xe400, IRQ 11, 00:00:b4:c6:0b:af.
e100: Intel(R) PRO/100 Network Driver, 3.5.23-k4-NAPI
e100: Copyright(c) 1999-2006 Intel Corporation
usbcore: registered new interface driver zd1201
console [netcon0] enabled
netconsole: network logging started
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
Probing IDE interface ide0...
hdb: WDC WD200BB-53AUA1, ATA DISK drive
hda: QUANTUM FIREBALLP LM30, ATA DISK drive
Probing IDE interface ide1...
hdd: CD-ROM 50X, ATAPI CD/DVD-ROM drive
hdc: HL-DT-ST DVDRAM GSA-4120B, ATAPI CD/DVD-ROM drive
Probing IDE interface ide2...
Probing IDE interface ide3...
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide1 at 0x170-0x177,0x376 on irq 15
hda: max request size: 128KiB
hda: 58633344 sectors (30020 MB) w/1900KiB Cache, CHS=58168/16/63
hda: cache flushes not supported
hda: hda1 hda2 hda3 hda4 < hda5 hda6 >
hdb: max request size: 128KiB
hdb: 39102336 sectors (20020 MB) w/2048KiB Cache, CHS=38792/16/63
hdb: cache flushes not supported
hdb: hdb1 hdb2
hdd: ATAPI 50X CD-ROM drive, 128kB Cache
Uniform CD-ROM driver Revision: 3.20
3ware Storage Controller device driver for Linux v1.26.02.002.
Driver 'sd' needs updating - please use bus_type methods
Driver 'sr' needs updating - please use bus_type methods
Fusion MPT base driver 3.04.06
Copyright (c) 1999-2007 LSI Corporation
Fusion MPT SPI Host driver 3.04.06
ieee1394: raw1394: /dev/raw1394 device initialized
usbmon: debugfs is not available
ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver
USB Universal Host Controller Interface driver v3.0
uhci_hcd 0000:00:07.2: UHCI Host Controller
uhci_hcd 0000:00:07.2: new USB bus registered, assigned bus number 1
uhci_hcd 0000:00:07.2: irq 10, io base 0x0000d400
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
usb 1-1: new low speed USB device using uhci_hcd and address 2
usb 1-1: configuration #1 chosen from 1 choice
usbcore: registered new interface driver usblp
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
usbcore: registered new interface driver libusual
PNP: No PS/2 controller found. Probing ports directly.
serio: i8042 KBD port at 0x60,0x64 irq 1
mice: PS/2 mouse device common for all mice
input: AT Translated Set 2 keyboard as /class/input/input0
input: PC Speaker as /class/input/input1
md: raid0 personality registered for level 0
md: raid1 personality registered for level 1
raid6: int32x1 97 MB/s
raid6: int32x2 94 MB/s
raid6: int32x4 110 MB/s
raid6: int32x8 104 MB/s
raid6: mmxx1 258 MB/s
raid6: mmxx2 298 MB/s
raid6: sse1x1 225 MB/s
raid6: sse1x2 305 MB/s
raid6: using algorithm sse1x2 (305 MB/s)
md: raid6 personality registered for level 6
md: raid5 personality registered for level 5
md: raid4 personality registered for level 4
device-mapper: ioctl: 4.12.0-ioctl (2007-10-02) initialised: [EMAIL PROTECTED]
input: Logitech USB-PS/2 Optical Mouse as /class/input/input2
input: USB HID v1.10 Mouse [Logitech USB-PS/2 Optical Mouse] on
usb-0000:00:07.2-1
usbcore: registered new interface driver usbhid
drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver
oprofile: using timer interrupt.
Netfilter messages via NETLINK v0.30.
nf_conntrack version 0.5.0 (8192 buckets, 32768 max)
ctnetlink v0.93: registering with nfnetlink.
ip_tables: (C) 2000-2006 Netfilter Core Team
IPVS: Registered protocols ()
IPVS: Connection hash table configured (size=4096, memory=32Kbytes)
IPVS: ipvs loaded.
TCP cubic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
ieee80211: 802.11 data/management/control stack, git-1.1.13
ieee80211: Copyright (C) 2004-2005 Intel Corporation <[EMAIL PROTECTED]>
ieee80211_crypt: registered algorithm 'NULL'
ieee80211_crypt: registered algorithm 'WEP'
Using IPI No-Shortcut mode
md: Autodetecting RAID arrays.
md: Scanned 0 and added 0 devices.
md: autorun ...
md: ... autorun DONE.
VFS: Mounted root (ext2 filesystem) readonly.
Freeing unused kernel memory: 284k freed
nvidia: module license 'NVIDIA' taints kernel.
NVRM: The NVIDIA GeForce2 MX/MX 400 GPU installed in this system is
NVRM: supported through the NVIDIA 96.43.xx Legacy drivers. Please
NVRM: visit http://www.nvidia.com/object/unix.html for more
NVRM: information. The 173.14.09 NVIDIA driver will ignore
NVRM: this GPU. Continuing probe...
NVRM: No NVIDIA graphics adapter found!
Linux video capture interface: v2.00
usb 1-2: new full speed USB device using uhci_hcd and address 3
usb 1-2: configuration #1 chosen from 1 choice
00:00.0 Host bridge: VIA Technologies, Inc. VT82C693A/694x [Apollo PRO133x]
(rev 42)
Flags: bus master, medium devsel, latency 0
Memory at ea000000 (32-bit, prefetchable) [size=32M]
Capabilities: [a0] AGP version 1.0
00:01.0 PCI bridge: VIA Technologies, Inc. VT82C598/694x [Apollo MVP3/Pro133x
AGP] (prog-if 00 [Normal decode])
Flags: bus master, 66MHz, medium devsel, latency 0
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
I/O behind bridge: 0000c000-0000cfff
Memory behind bridge: e8000000-e9ffffff
Prefetchable memory behind bridge: e0000000-e7ffffff
Capabilities: [80] Power Management version 2
00:07.0 ISA bridge: VIA Technologies, Inc. VT82C596 ISA [Mobile South] (rev 12)
Subsystem: VIA Technologies, Inc. VT82C596/A/B PCI to ISA Bridge
Flags: bus master, stepping, medium devsel, latency 0
00:07.1 IDE interface: VIA Technologies, Inc.
VT82C586A/B/VT82C686/A/B/VT823x/A/C PIPC Bus Master IDE (rev 06) (prog-if 8a
[Master SecP PriP])
Flags: bus master, medium devsel, latency 64
[virtual] Memory at 000001f0 (32-bit, non-prefetchable) [size=8]
[virtual] Memory at 000003f0 (type 3, non-prefetchable) [size=1]
[virtual] Memory at 00000170 (32-bit, non-prefetchable) [size=8]
[virtual] Memory at 00000370 (type 3, non-prefetchable) [size=1]
I/O ports at d000 [size=16]
00:07.2 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1
Controller (rev 08) (prog-if 00 [UHCI])
Subsystem: VIA Technologies, Inc. (Wrong ID) USB Controller
Flags: bus master, medium devsel, latency 64, IRQ 10
I/O ports at d400 [size=32]
Kernel driver in use: uhci_hcd
00:07.3 Host bridge: VIA Technologies, Inc. VT82C596 Power Management (rev 20)
Flags: medium devsel
00:09.0 Multimedia audio controller: Creative Labs SB Live! EMU10k1 (rev 07)
Subsystem: Creative Labs SBLive! 5.1 Model SB0100
Flags: bus master, medium devsel, latency 64, IRQ 12
I/O ports at d800 [size=32]
Capabilities: [dc] Power Management version 1
00:09.1 Input device controller: Creative Labs SB Live! Game Port (rev 07)
Subsystem: Creative Labs Gameport Joystick
Flags: bus master, medium devsel, latency 64
I/O ports at dc00 [size=8]
Capabilities: [dc] Power Management version 1
00:0b.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8029(AS)
Subsystem: Realtek Semiconductor Co., Ltd. RTL-8029(AS)
Flags: medium devsel, IRQ 5
I/O ports at e000 [size=32]
Kernel driver in use: ne2k-pci
00:0c.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8029(AS)
Subsystem: Realtek Semiconductor Co., Ltd. RTL-8029(AS)
Flags: medium devsel, IRQ 11
I/O ports at e400 [size=32]
Kernel driver in use: ne2k-pci
01:00.0 VGA compatible controller: nVidia Corporation NV11 [GeForce2 MX/MX 400]
(rev a1) (prog-if 00 [VGA controller])
Subsystem: Micro-Star International Co., Ltd. Device 8818
Flags: bus master, 66MHz, medium devsel, latency 64, IRQ 11
Memory at e8000000 (32-bit, non-prefetchable) [size=16M]
Memory at e0000000 (32-bit, prefetchable) [size=128M]
Expansion ROM at e9000000 [disabled] [size=64K]
Capabilities: [60] Power Management version 2
Capabilities: [44] AGP version 2.0
Kernel modules: nvidia
Bus 001 Device 003: ID 0bda:8189 Realtek Semiconductor Corp.
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 2.00
bDeviceClass 0 (Defined at Interface level)
bDeviceSubClass 0
bDeviceProtocol 0
bMaxPacketSize0 64
idVendor 0x0bda Realtek Semiconductor Corp.
idProduct 0x8189
bcdDevice 2.00
iManufacturer 1 Manufacturer_Realtek
iProduct 2 RTL8187B_WLAN_Adapter
iSerial 3 00e04c000001
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 81
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 4 Wireless Network Card
bmAttributes 0x80
(Bus Powered)
MaxPower 500mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 9
bInterfaceClass 255 Vendor Specific Class
bInterfaceSubClass 255 Vendor Specific Subclass
bInterfaceProtocol 255 Vendor Specific Protocol
iInterface 2 RTL8187B_WLAN_Adapter
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x83 EP 3 IN
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0040 1x 64 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x04 EP 4 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0040 1x 64 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x05 EP 5 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0040 1x 64 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x06 EP 6 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0040 1x 64 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x07 EP 7 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0040 1x 64 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x89 EP 9 IN
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0040 1x 64 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x0a EP 10 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0040 1x 64 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x0b EP 11 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0040 1x 64 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x0c EP 12 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0040 1x 64 bytes
bInterval 0
Device Qualifier (for other device speed):
bLength 10
bDescriptorType 6
bcdUSB 2.00
bDeviceClass 0 (Defined at Interface level)
bDeviceSubClass 0
bDeviceProtocol 0
bMaxPacketSize0 64
bNumConfigurations 1
Device Status: 0x0000
(Bus Powered)
Bus 001 Device 002: ID 046d:c00e Logitech, Inc. M-BJ69 Optical Wheel Mouse
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 2.00
bDeviceClass 0 (Defined at Interface level)
bDeviceSubClass 0
bDeviceProtocol 0
bMaxPacketSize0 8
idVendor 0x046d Logitech, Inc.
idProduct 0xc00e M-BJ69 Optical Wheel Mouse
bcdDevice 11.00
iManufacturer 1 Logitech
iProduct 2 USB-PS/2 Optical Mouse
iSerial 0
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 34
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 0
bmAttributes 0xa0
(Bus Powered)
Remote Wakeup
MaxPower 98mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 1
bInterfaceClass 3 Human Interface Devices
bInterfaceSubClass 1 Boot Interface Subclass
bInterfaceProtocol 2 Mouse
iInterface 0
HID Device Descriptor:
bLength 9
bDescriptorType 33
bcdHID 1.10
bCountryCode 0 Not supported
bNumDescriptors 1
bDescriptorType 34 Report
wDescriptorLength 52
Report Descriptors:
** UNAVAILABLE **
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0004 1x 4 bytes
bInterval 10
Device Status: 0x0000
(Bus Powered)
Bus 001 Device 001: ID 0000:0000
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 1.10
bDeviceClass 9 Hub
bDeviceSubClass 0 Unused
bDeviceProtocol 0
bMaxPacketSize0 64
idVendor 0x0000
idProduct 0x0000
bcdDevice 2.06
iManufacturer 3 Linux 2.6.24 uhci_hcd
iProduct 2 UHCI Host Controller
iSerial 1 0000:00:07.2
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 25
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 0
bmAttributes 0xe0
Self Powered
Remote Wakeup
MaxPower 0mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 1
bInterfaceClass 9 Hub
bInterfaceSubClass 0 Unused
bInterfaceProtocol 0
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0002 1x 2 bytes
bInterval 255
Hub Descriptor:
bLength 9
bDescriptorType 41
nNbrPorts 2
wHubCharacteristic 0x000a
No power switching (usb 1.0)
Per-port overcurrent protection
bPwrOn2PwrGood 1 * 2 milli seconds
bHubContrCurrent 0 milli Ampere
DeviceRemovable 0x00
PortPwrCtrlMask 0xff
Hub Port Status:
Port 1: 0000.0303 lowspeed power enable connect
Port 2: 0000.0103 power enable connect
Device Status: 0x0003
Self Powered
Remote Wakeup Enabled
