Hi Ravi, (could you please keep mail on the public list so others can learn from the experience as well)
Unfortunately you are hitting trunk when it is in a volatile state. We just had a code sprint a few weekends ago, and part of what we did move the web module to a folder called "legacy". To pick it up we use what is called a "mvn profile". Basically any time you want do a maven command, you need the switch -P legacy to include the old web module. We are also avtively working on a new web module to take its place, named web2, it lives in teh community folder. To enable it you use the probile "web2". So, to compile with the old web module: mvn -P legacy clean install Where the web module will be found under legacy/web. Hope that helps. Let me know if you have any more problems. Again my apologies for the state of trunk right now. -Justin Ravichandra K.N wrote: > Thanks for your reply. > > Now i was able to build successfully. but what next i didn't understand. > > let me tell you the steps i followed. > > 1. created a folder geoserver_dev in c: drive. [i'm using windows]. > > 2. then svn checkout https://svn.codehaus.org/geoserver/trunk/src > <http://svn.codehaus.org/geoserver/trunk/src> > i did the check using above url. Inside c:\geoserver_dev. It checked in > all the folders as it was shown in the site. > > 3. mvn install. this time mvn install was Build successful. This > commonad executed from c:\geoserver_dev\src. > > 4. now i'm not able to find the web directory, to start the Jetty:run. i > didn't find the /web directory inside my geoserver_dev folder. I was > trying to execute the command from the same path. but i was not able to. > > Please let me know where i have to find the /web directory. I tried from > .m2 repository but i could not find there. > > I'm bit confused how to run the jetty. [:(] > > Hope you understood my problem. > > regards, > Ravi > > > On Thu, Mar 5, 2009 at 9:12 PM, Justin Deoliveira <[email protected] > <mailto:[email protected]>> wrote: > > Hi Ravi, > > it is a little out of date but the maven quickstart can be found here: > > http://geoserver.org/display/GEOSDOC/2+Maven+Quickstart > > It would help if you included the failures you are getting so we can > better comment on what might be wrong. > > Another thing to keep in mind is that trunk can be unstable at > times, and it might just be that the build is broken. You can check > this by visiting http://hudson.opengeo.org/hudson/, and noting the > status of "geoserver-trunk". Which at the moment appears to be down :( > > -Justin > > ravichandrakn wrote: > > Hi All, > > I'm new to this community, I'm trying to Build geoserver using > maven. > > the following are the version i'm using. > apache-maven-2.0.10 > subversion: svn-1.3.0-setup > > After i checkout the geoserver code from svn checkout > https://svn.codehaus.org/geoserver/trunk > i was trying to build using mvn install. Build failure and 8 > failures its > showing. > I don't know why it's throwing so may failures. > Can anyone please post the step-by-step procedure to build > geoserver using > maven. The Available reference in geoser.org <http://geoser.org> > is too confusing and didn't > explain properly. > > regards, > Ravi. > > > > > > -- > Justin Deoliveira > OpenGeo - http://opengeo.org > Enterprise support for open source geospatial. > > > > > -- > Regards, > Ravi, > Integra Micro Systems(P) ltd, > Bangalore-92. > +919845787811 -- Justin Deoliveira OpenGeo - http://opengeo.org Enterprise support for open source geospatial. ------------------------------------------------------------------------------ _______________________________________________ Geoserver-devel mailing list [email protected] https://lists.sourceforge.net/lists/listinfo/geoserver-devel
