Hi, Yes, I did. The status shows all as completed.
Regards, Jeevan. On Mon 24 Sep, 2018, 9:20 PM Nithya Balachandran, <[email protected]> wrote: > > > On 24 September 2018 at 21:01, Jeevan Patnaik <[email protected]> wrote: > >> Hi, >> >> What do you mean by expanding volume? >> >> I mean adding new bricks to extend storage. It is mentioned that >> detaching tier is must for adding or removing bricks. >> >> What command did you use to detach the tier? And how did you check that >> the files still exist on the hot tier? >> >> gluster volume tier volume_name detach start >> >> I check the files directly from backend filesystem on disk and there are >> still left over files on all hot tier disks. >> >> Anyhow I proceeded with detach commit to see what would happen..so after >> commit, I can't access those files from client filesystems..so they're gone >> with the hot tier and were not moved to cold tier. >> > > Did you check that the detach tier operation had completed before running > detach commit? > >> >> And even if I try to attach the hot tier bricks again to bring back the >> files, attach won't work with existing files. >> >> So, it seems we shouldn't detach hot tier without making sure all files >> are moved to cold tier..but in my case, some files just won't move, even >> though they aren't being accessed anywhere. >> > > > >> >> There's a statement saying POSIX locks can cause files to be still left >> in hot tier and in that case, either the application causing posix lock has >> to be closed or files should be moved manually (but where?)... however, I >> don't think in my case there's any posix locks as the files are not >> accessed by any application except gluster itself. >> >> Regards, >> Jeevan. >> >> >> On Mon 24 Sep, 2018, 8:45 PM Nithya Balachandran, <[email protected]> >> wrote: >> >>> It has been a while since I worked on tier but here is what I remember: >>> >>> >>> On 24 September 2018 at 19:15, Jeevan Patnaik <[email protected]> >>> wrote: >>> >>>> Hi Nithya, >>>> >>>> No..the files are not being accessed. And tiering mode is in cache mode >>>> and what I understood is in cache mode every file is moved to hot tier >>>> until it reaches low watermark, then it only promotes highly accessed >>>> files. >>>> >>>> Not quite . All files will initially exist on the cold tier. Any new >>> files will be created on the hot tier. Any old files that are accessed will >>> be promoted ot the hot tier. >>> >>> >>> And do you mean everytime we expand volume, we are virtually flushing >>>> the tier and it regenerates only when a files are accessed? >>>> >>>> What do you mean by expanding the volume? >>> >>> >>>> Also I see one more issue now, I hav generated another 1000 files after >>>> tiering is started and I see all 1000 files are now created on hot tier. >>>> Now, I detached again..in detach status it shows completed..but when I >>>> checked, around 260 files are still located on hot tier..those files are >>>> not being used anywhere..ca you tell why are they still not moved to cold >>>> tier and why the detach status is showing a wrong status. >>>> >>> >>> What command did you use to detach the tier? And how did you check that >>> the files still exist on the hot tier? >>> >>> Regards, >>> Nithya >>> >>>> >>>> I am using gluster 3.12.3 and server hosts include RHEL 6.7 and 7.2 >>>> hosts also. >>>> >>>> Regards, >>>> Jeevan. >>>> >>>> On Mon 24 Sep, 2018, 7:00 PM Nithya Balachandran, <[email protected]> >>>> wrote: >>>> >>>>> Are those files being accessed? Tiering will only promote those that >>>>> have been accessed recently. >>>>> >>>>> Regards, >>>>> Nithya >>>>> >>>>> On 24 September 2018 at 18:32, Jeevan Patnaik <[email protected]> >>>>> wrote: >>>>> >>>>>> I see it still not promoting any files. Do we need to run any command >>>>>> to force the movement? >>>>>> >>>>>> This would be an issue if we need to expand disk as then we also need >>>>>> to detach existing tier and attach again and expect the data to be >>>>>> promoted >>>>>> to the hot tier. >>>>>> >>>>>> Regards, >>>>>> Jeevan. >>>>>> >>>>>> On Mon 24 Sep, 2018, 6:17 PM Jeevan Patnaik, <[email protected]> >>>>>> wrote: >>>>>> >>>>>>> Hi, >>>>>>> >>>>>>> I have created a 18 disk replica 3 volume and created 1000 random >>>>>>> files each of 10M. >>>>>>> >>>>>>> Later I have attached 15 disk replica 3 tier with each hot tier disk >>>>>>> coming from cold tier host, except on 3 (as we don't have hot tier disk) >>>>>>> >>>>>>> After attach, I see no files are promoted at even after 15 minutes. >>>>>>> Status is showing as In progress. >>>>>>> >>>>>>> Is it always this much slow? For 10G data, 15 minutes is too much >>>>>>> Also will the data try to be promoted to a hot tier coming from the >>>>>>> same host to reduce the time taken to move the files? >>>>>>> >>>>>>> Cold tier is made of RAID supported SSD and hot tier is made of NVMe >>>>>>> SSDs. >>>>>>> >>>>>>> >>>>>>> Regards, >>>>>>> Jeevan. >>>>>>> >>>>>> >>>>>> _______________________________________________ >>>>>> Gluster-users mailing list >>>>>> [email protected] >>>>>> https://lists.gluster.org/mailman/listinfo/gluster-users >>>>>> >>>>> >>>>> >>> >
_______________________________________________ Gluster-users mailing list [email protected] https://lists.gluster.org/mailman/listinfo/gluster-users
