Robert
thank you !I find that file which you said .But i am not sure which
fuction read step file. Is it loadstep()? As a matter of fact ,I want to konw
that how read the data of step file,and which dates are transfered to mesh
generation module.Those fuction are realized
by which fuction. Can you said more detailedly.I konw a little about GMsh.
liang
--- 09年1月3日，周六, Robert Funnell <[email protected]> 写道：
发件人: Robert Funnell <[email protected]>
主题: Re: [Gmsh] About read *.step file function？
收件人: "liang dong" <[email protected]>
抄送: "gmsh" <[email protected]>
日期: 2009,13,周六,7:13上午
Liang -
The code for reading .step files is in Geo/GModelIO_OCC.cpp.
I found it by examining Common/OpenFile.cpp and then doing
find ./ -name \*.cpp -exec grep -H readOCCSTEP {} \;
Is that the information that you're looking for?
- Robert
On Fri, 2 Jan 2009, liang dong wrote:
> thank you your reply ! I only want to konw the read *.step file in
gmsh source code.Somebody tell me the fuction or tell me how to find it?
>
dongliang
>
> --- 08ÿÿ12ÿÿ31ÿÿÿÿÿÿÿÿ, wing <[email protected]>
ÿÿÿÿÿÿ
>
> ÿÿÿÿÿÿ: wing <[email protected]>
> ÿÿÿÿ: Re: [Gmsh] About read *.step file functionÿÿ
> ÿÿÿÿÿÿ: [email protected]
> ÿÿÿÿ: "gmsh" <[email protected]>
> ÿÿÿÿ: 2008,1231,ÿÿÿÿ,7:36ÿÿÿÿ
>
> liang dong wrote:
>> hi wing
>> Once again, thank you so much! sorry,I donot konw the mean"
gmsh
> your_file_name.step
>> ' ,I want to kown the fuction read *.step file .And the mesh
modle
> need which information come from *.step file ? Thanks you very much!
>>
> liang
>> --- *08ÿÿ12ÿÿ27ÿÿÿÿÿÿÿÿ, wing
/<[email protected]>/*
> ÿÿÿÿÿÿ
>>
>> ÿÿÿÿÿÿ: wing <[email protected]>
>> ÿÿÿÿ: Re: [Gmsh] About read *.step file functionÿÿ
>> ÿÿÿÿÿÿ: [email protected]
>> ÿÿÿÿ: [email protected]
>> ÿÿÿÿ: 2008,1227,ÿÿÿÿ,8:57ÿÿÿÿ
>>
>> liang dong wrote:
>> > hiÿÿ
>> > I have problem about *.step file .I want to konw how to read
> *.step
>> > file in gmsh? Is "loadstep()" function? Can you tell
me
> where
>> the
>> > function read the *step ?I cannot find it.
>> > Thank you very much!!
>> > dongliang
>> >
>> >
>> >
> ------------------------------------------------------------------------
>> >
ÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿ
>> >
>>
>
<http://cn.rd.yahoo.com/mail_cn/tagline/card/*http://card.mail.cn.yahoo.com/>
>> >
>> >
> ------------------------------------------------------------------------
>> >
>> > _______________________________________________
>> > gmsh mailing list
>> > [email protected]
>> > http://www.geuz.org/mailman/listinfo/gmsh
>> > Hi dongliang,
>> I'm not sure if there exists a loadstep() function, but when
it
> comes to
>> how to read *.step file in gmsh, you can try this:
>> gmsh your_file_name.step
>>
>> hope this helps.
>>
>> wing
>>
>>
>>
------------------------------------------------------------------------
>> ÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿ
>
<http://cn.rd.yahoo.com/mail_cn/tagline/card/*http://card.mail.cn.yahoo.com/>
>
>
> Hi dongliang,
> Seems that you are talking about the source code? I'm sorry I'm
not
> familiar with programming, even the source code itself, but I believe
somebody
> here can help if your question is described in more detail.
> BTW, you should cc your mail to the mailing list <[email protected]> so
that
> everyone in the list can receive your message. Use "Reply to
all"
> rather than just "Reply" next time.
> Good luck.
>
> wing
>
>
>
> ___________________________________________________________
> ÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿ
> http://card.mail.cn.yahoo.com/
___________________________________________________________
好玩贺卡等你发，邮箱贺卡全新上线！
http://card.mail.cn.yahoo.com/_______________________________________________
gmsh mailing list
[email protected]
http://www.geuz.org/mailman/listinfo/gmsh
