I am trying to do a simple example for Fluidity which first requires me to set
up a mesh in Gmsh, but it's not working and I can't see why. I am using the
following .geo file:
Point(1) = {5.0, 0.0, 0.0, 0.1};
Point(2) = {35.0, 0.0, 0.0, 0.1};
Point(3) = {35.0, 2.0, 0.0, 0.1};
Point(4) = {30.0, 2.0, 0.0, 0.05};
Point(5) = {30.0, 4.05, 0.0, 0.1};
Point(6) = {0.0, 4.05, 0.0, 0.1};
Point(7) = {0.0, 2.05, 0.0, 0.1};
Point(8) = {5.0, 2.0, 0.0, 0.05};
Point(9) = {5.0, 2.05, 0.0, 0.05};
Point(10) = {30.0, 2.05, 0.0, 0.05};
Line(1) = {1,2};
Line(2) = {2,3};
Line(3) = {3,4};
Line(4) = {4,8};
Line(5) = {8,1};
Line(6) = {7,9};
Line(7) = {9,10};
Line(8) = {10,5};
Line(9) = {5,6};
Line(10) = {6,7};
Line(11) = {8,9};
Line(12) = {10,4};
Line Loop(13) = {1,2,3,4,5};
Line Loop(14) = {6,7,8,9,10};
Line Loop(15) = {4,11,7,12};
Plane Surface(16) = {13};
Plane Surface(17) = {14};
Plane Surface(18) = {15};
Line Loop(19) = {1,2,3,-12,8,9,10,6,-11,5};
Physical Surface(20) = {13,14,15};
//Inflows
Physical Line(21) = {2};
Physical Line(22) = {10};
//Outlets
Physical Line(23) = {5};
Physical Line(24) = {8};
//Top and bottom
Physical Line(25) = {9};
Physical Line(26) = {1};
//Less sure about these
Physical Line(27) = {6,11};
Physical Line(28) = {3,12};
The commands "gmsh -2 -v 0 a2wayflow.geo" and "gmsh -2 -v 0 a2wayflow.geo" both
seem to work fine. The problem occurs when I do "gmsh2triangle -2
a2wayflow.msh" for use in Fluidity, I get the error "Unable to determine
dimension of problem". Using the GUI, pretty much the same thing happens. Mesh
generates no problem, looks OK, saves without complaining, then running the
gmsh2triangle command gets the same error message.
I've thoroughly looked at it several times and a colleague who is much more
experienced with it than me can't spot the problem either, can you tell me
where I'm going wrong? Or is the problem at the Fluidity end?
Penny Jackson.
Penelope Jackson
Scientist
[dstl] Sensors & Countermeasures Department
Rm 101, iSAT-C, Bldg 5
Dstl Porton Down
T 9 6801 8413
"This e-mail and any attachment(s) is intended for the recipient only. Its
unauthorised use,
disclosure, storage or copying is not permitted. Communications with Dstl are
monitored and/or
recorded for system efficiency and other lawful purposes, including business
intelligence, business
metrics and training. Any views or opinions expressed in this e-mail do not
necessarily reflect Dstl policy."
"If you are not the intended recipient, please remove it from your system and
notify the author of
the email and [email protected]"
_______________________________________________
gmsh mailing list
[email protected]
http://www.geuz.org/mailman/listinfo/gmsh
