Thanks. I will look up the manual again.

Quoting Sander Pronk <[email protected]>:

Hi Nisha,

Looking at your .mdp, there are some issues that might lead to the behavior that you describe: First: you should try to look up the published densities for tip3p water at 300K - they might actually be close to what you get. Second: your neighbor list cut-off (rlist) might be too small to fully contain the charge groups (check the manual, section 7.3.11). Third: You haven't enabled long-range mean field correction for the pressure or energy. Expect the pressure to be strongly dependent on cut-off (see the same section).

Sander


On Mar 30, 2010, at 22:47 , [email protected] wrote:

I have a box (3x3x3nm) of Tip3p water molecules ~900 and the density when I create the box using genbox is 997.177g/l. I did energy minimization run and the potential energy did converge smoothly, so I did NPT equilibration run of 100ps and I got the density value of 975g/l. Why does the density decrease after the run? these are the parameters that I used :

RUN CONTROL PARAMETERS
integrator               = md
tinit                    = 0
dt                       = 0.002
nsteps                   = 50000
nstcomm                  = 0
nstxout                  = 0
nstvout                  = 0
nstfout                  = 0
nstlog                   = 100
nstenergy                = 100
nstxtcout                = 0
xtc_precision            = 1000
nstlist                  = 5
ns-type                  = Grid
pbc                      = xyz
rlist                    = 1.1
coulombtype              = pme
rcoulomb                 = 1.1
epsilon-r                = 1
vdw-type                 = switch
rvdw-switch              = 0.8
rvdw                     = 1.0
Tcoupl                   = V-rescale
tc-grps                  = System
tau_t                    = 0.1
ref_t                    = 300
Pcoupl                   = berendsen
tau_p                    = 0.5
compressibility          = 4e-05
ref_p                    = 1.0
constraints              = all-bonds
constraint-algorithm     = Lincs
unconstrained-start      = no
lincs-order              = 4
lincs-iter               = 1
lincs-warnangle          = 30

Am I missing something?
Thanks

Nisha Patel


--
gmx-users mailing list    [email protected]
http://lists.gromacs.org/mailman/listinfo/gmx-users
Please search the archive at http://www.gromacs.org/search before posting!
Please don't post (un)subscribe requests to the list. Use the
www interface or send it to [email protected].
Can't post? Read http://www.gromacs.org/mailing_lists/users.php

--
gmx-users mailing list    [email protected]
http://lists.gromacs.org/mailman/listinfo/gmx-users
Please search the archive at http://www.gromacs.org/search before posting!
Please don't post (un)subscribe requests to the list. Use the
www interface or send it to [email protected].
Can't post? Read http://www.gromacs.org/mailing_lists/users.php




Nisha Patel
MSc Candidate
Leslie Dan Faculty of Pharmacy
Department of Pharmaceutical Sciences
144 College Street
Room 1172
Toronto, ON
M5S 3M2
Canada
Telephone: 416-978-1536

--
gmx-users mailing list    [email protected]
http://lists.gromacs.org/mailman/listinfo/gmx-users
Please search the archive at http://www.gromacs.org/search before posting!
Please don't post (un)subscribe requests to the list. Use the
www interface or send it to [email protected].
Can't post? Read http://www.gromacs.org/mailing_lists/users.php

Reply via email to