I think I have a SSD on the way out. Last reboot took a REALLY long time. Like 30 minutes. I ran the smart data and self test and the SSD passes. Overall assessment is disk is ok. I really don't know how to interpret what the results are.
I think the disk is in pre-fail based on the smartctl output below /snip === START OF INFORMATION SECTION === Model Family: Crucial/Micron RealSSD m4/C400/P400 Device Model: M4-CT256M4SSD2 Serial Number: 000000001247091DC2FF LU WWN Device Id: 5 00a075 1091dc2ff Firmware Version: 040H User Capacity: 256,060,514,304 bytes [256 GB] Sector Size: 512 bytes logical/physical Rotation Rate: Solid State Device Form Factor: 2.5 inches Device is: In smartctl database [for details use: -P show] ATA Version is: ACS-2, ATA8-ACS T13/1699-D revision 6 SATA Version is: SATA 3.0, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Wed Dec 30 13:49:17 2020 EST SMART support is: Available - device has SMART capability. SMART support is: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED /snip ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE 1 Raw_Read_Error_Rate 0x002f 100 100 050 Pre-fail Always - 0 5 Reallocated_Sector_Ct 0x0033 100 100 010 Pre-fail Always - 0 9 Power_On_Hours 0x0032 100 100 001 Old_age Always - 7294 12 Power_Cycle_Count 0x0032 100 100 001 Old_age Always - 2511 170 Grown_Failing_Block_Ct 0x0033 100 100 010 Pre-fail Always - 0 171 Program_Fail_Count 0x0032 100 100 001 Old_age Always - 0 172 Erase_Fail_Count 0x0032 100 100 001 Old_age Always - 0 173 Wear_Leveling_Count 0x0033 098 098 010 Pre-fail Always - 66 174 Unexpect_Power_Loss_Ct 0x0032 100 100 001 Old_age Always - 87 181 Non4k_Aligned_Access 0x0022 100 100 001 Old_age Always - 10250 5047 5203 183 SATA_Iface_Downshift 0x0032 100 100 001 Old_age Always - 0 184 End-to-End_Error 0x0033 100 100 050 Pre-fail Always - 0 187 Reported_Uncorrect 0x0032 100 100 001 Old_age Always - 0 188 Command_Timeout 0x0032 100 100 001 Old_age Always - 0 189 Factory_Bad_Block_Ct 0x000e 100 100 001 Old_age Always - 81 194 Temperature_Celsius 0x0022 100 100 000 Old_age Always - 0 195 Hardware_ECC_Recovered 0x003a 100 100 001 Old_age Always - 0 196 Reallocated_Event_Count 0x0032 100 100 001 Old_age Always - 0 197 Current_Pending_Sector 0x0032 100 100 001 Old_age Always - 0 198 Offline_Uncorrectable 0x0030 100 100 001 Old_age Offline - 0 199 UDMA_CRC_Error_Count 0x0032 100 100 001 Old_age Always - 0 202 Perc_Rated_Life_Used 0x0018 098 098 001 Old_age Offline - 2 206 Write_Error_Rate 0x000e 100 100 001 Old_age Always - 0 Replace the disk pronto? Is that what this is telling me? Or? I recently copied over many important files to another disk. And downloaded a new OS. I just hate re-configuring things, and starting from scratch, it's such a pain. Not as painful as a disk crash, but close. I've got loads of stuff I've compiled from source and just 100's of things to check or update. Yes, I'll just have to do it. It's just the week plus of recovery that I'm rebelling against. Anything else I should do first? Check something? Run a test? Any tips to make the "recovery" less painful? _______________________________________________ gnhlug-discuss mailing list gnhlug-discuss@mail.gnhlug.org http://mail.gnhlug.org/mailman/listinfo/gnhlug-discuss/
