I have installed the following: ktoblzcheck-1.15-42.pm.1 libktoblzcheck1-1.15-42.pm.1 aqbanking-2.3.2-0.pm.1 aqbanking-qt3-2.3.2-0.pm.1 libaqbanking16-2.3.2-0.pm.1 libaqhbci10-2.3.2-0.pm.1
and GnuCash 2.2.1 on x86_64 from [1] and I have hbci setup in Tools. I don't know which aqbanking packages you installed, those from packman or some others? I did not try i586, but I suppose it works too. Regards, Chris [1] ftp://ftp.rauchs-home.de/suse/10.2/x86_64/gnucash-2.2.1-0.rauch.1.x86_64.rpm John Sved schrieb: > Hi Chris, > > I used the openSuSE 10.2 disk via YAST to check and install where necessary: > > gtk2-devel > guile > guile-devel > pkgconfig > perl-XML-Parser > perl > libxml2-devel > libgnomeui-devel > libgnomeprint-devel > libgnomeprintui-devel > libglade2-devel > gtkhtml2-devel > doxygen > opensp > opensp-devel > gwenhywfar-devel > goffice-devel > libtool > > From RPM pbone.net > > libktoblzcheck-devel > > Then from RPM pbone.net the following were downloaded. The order is > as they were installed after an dependency warnings. (i.e. this will > save others going back to to fetch yet another RPM ! note make sure > that it is the right version for openSuSE or SuSE) > > libaqhbci10 2.3.2 > libaqbanking16 2.3.2 > libaqbanking-devel 2.3.2 > libaqdtaus.so.3 > libqbanking.so.4 > libcbanking.so.16 > aqbankinking-qt3 2.3.2 > aqbanking 2.3.2 > > > Then ./configure --enable-hbci > make > make install > > It worked ! but no setup HBCI in the tools menu :( > > So 3 hours of effort has not yet delivered the desired gnucash 2.2.1 > with HBCI. > > Any suggestions ? > > regards > John > > > > Rauch Christian wrote: > >> John Sved schrieb: >> >>> Hi, >>> >>> I am really just a user of gnucash. As I want to use the HBCI function >>> which is not included in the binary RPM for openSuSE 10.2 I am >>> reluctantly prepared to try to compile the source. >>> >> My Gnucash rpm is built against aqbanking, which provides HBCI. >> You will have to install one of aqbanking-qt3 or aqbanking-gtk2 from >> packman including their aqbanking to get the wizard in gnucash. >> >> >>> The aqbanking 2.2.3 from distro RPM and libqwenhwfar 2.6.1 from >>> downloaded RPM are installed >>> >> Use aqbanking 2.3.2 from packman (see above). >> >> >>> So if someone would like to walk me through it, we may find the >>> necessary pieces to actually compile gnucash 2.2.1 with HBCI on >>> opensSuSE 10.2 for others to follow and avoid wasting a lot of time. >>> >> Complete build requirements for Gnucash on Suse 10.2 are as follows: >> >> aqbanking libaqbanking-devel gtk2-devel guile guile-devel pkgconfig >> perl-XML-Parser perl libxml2-devel libgnomeui-devel libgnomeprint-devel >> libgnomeprintui-devel libglade2-devel gtkhtml2-devel doxygen opensp >> opensp-devel gwenhywfar-devel goffice-devel libtool libktoblzcheck-devel >> >> These may fetch some additional requirements I did not state explicitely. >> >> >> >>> Thanks, >>> >>> John >>> >> Regards, >> Chris >> >> >> _______________________________________________ gnucash-devel mailing list [email protected] https://lists.gnucash.org/mailman/listinfo/gnucash-devel
