On Dec 11, 2011, at 11:30 AM, David Reiser wrote: > On Dec 11, 2011, at 1:41 PM, John Ralls wrote: > >> >> On Dec 10, 2011, at 10:23 PM, David Reiser wrote: >> >>> >>> On Dec 11, 2011, at 12:39 AM, John Ralls wrote: >>> >>>> >>>> On Dec 10, 2011, at 8:03 PM, David Reiser wrote: >>>> >>>>> r21708 fixed my build problem (thanks John), but gnucash fails to launch >>>>> with: >>>>> >>>>> Backtrace: >>>>> In unknown file: >>>>> ?: 21* [#<procedure #f ()>] >>>>> ?: 22* (let* ((file #)) (cond (# => #) (# => #))) >>>>> ?: 23 [#<procedure #f #> >>>>> "/opt/gnucash-svn/share/gnucash/guile-modules/gnucash/report/standard-reports.scm"] >>>>> ?: 24 [with-fluid* #<fluid 7> #f #<procedure #f ()>] >>>>> ?: 25* [#<procedure #f ()>] >>>>> ?: 26* [load-file #<primitive-procedure primitive-load> ...] >>>>> ?: 27* [save-module-excursion #<procedure #f ()>] >>>>> ?: 28 (let (# #) (dynamic-wind # thunk #)) >>>>> ?: 29 [dynamic-wind #<procedure #f ()> #<procedure #f ()> #<procedure #f >>>>> ()>] >>>>> ?: 30* [#<procedure #f ()>] >>>>> ?: 31* [primitive-load >>>>> "/opt/gnucash-svn/share/gnucash/guile-modules/gnucash/report/standard-reports.scm"] >>>>> In >>>>> /opt/gnucash-svn/share/gnucash/guile-modules/gnucash/report/standard-reports.scm: >>>>> 125: 32* [for-each #<procedure #f (x)> (trial-balance transaction >>>>> sx-summary ...)] >>>>> In unknown file: >>>>> ?: 33* [#<procedure #f (x)> balsheet-eg] >>>>> In >>>>> /opt/gnucash-svn/share/gnucash/guile-modules/gnucash/report/standard-reports.scm: >>>>> 127: 34* [module-use! #<directory (gnucash report standard-reports) >>>>> 109f68880> ... >>>>> 129: 35* [resolve-interface (gnucash report standard-reports balsheet-eg)] >>>>> In unknown file: >>>>> ?: 36 (letrec ((get-keyword-arg #)) (let* (# # # ...) (and # #) ...)) >>>>> ?: 37 (let* (# # # # ...) (and # #) (if # public-i #)) >>>>> ?: 38* (and (or (not module) (not public-i)) (error "no code for module" >>>>> name)) >>>>> ?: 39 [error "no code for module" (gnucash report standard-reports >>>>> balsheet-eg)] >>>>> ... >>>>> ?: 40 [scm-error misc-error #f ...] >>>>> >>>>> <unnamed port>: In procedure scm-error in expression (scm-error (quote >>>>> misc-error) #f ...): >>>>> <unnamed port>: no code for module (gnucash report standard-reports >>>>> balsheet-eg) >>>>> >>>>> This looks like it might be related to moving balsheet-eg in r21591. >>>>> Geert, could you take a look? >>>>> >>>> >>>> Try: >>>> make maintainer-clean >>>> find src -name gnucash -type d >>>> rm -rf everything you find *except* gnc-module/(foo|bar|baz)/gnucash >>>> >>>> Then autogen, configure, build, and install and try again. >>>> >>>> Regards, >>>> John Ralls >>>> >>> I didn't exactly follow part of that: the found files were: >>> src/gnc-module/test/mod-bar/gnucash >>> src/gnc-module/test/mod-baz/gnucash >>> src/gnc-module/test/mod-foo/gnucash >>> >>> Looking at the contents of one of those directories looked like it wouldn't >>> interfere on launch. If any of those should be removed, let me know and >>> I'll try again. >>> >>> But the source directory was a completely clean checkout from yesterday >>> afternoon, and the only config/build activity was the build failure fixed >>> in 21708. >>> >>> No change in result on launching gnucash. I do rm -rf base/install/dir >>> too, before installing the new version in an old location. >> >> David, >> >> Sorry, yes, those are the directories I meant. >> >> What about your installation directories? Might they still have old Scheme >> files or shared libraries? >> >> Try removing (rm -rf) lib/gnucash and share/gnucash, then re-running make >> install. >> >> I just tested r21710 and it started up OK -- but I did have to clean out the >> installation and reinstall for it to work. >> >> Regards, >> John Ralls >> > Still no joy for me. I almost always rm -rf $PREFIX/* before make install > (needed once in the deep dark past, so I got in the habit of doing it every > time). I also removed lib/gnucash and share/gnucash before reinstalling. > > My guile is not in a standard location, but that hasn't been a problem > before. I'm using guile 1.8.8 and swig 2.0.4
OK, then it's not an installation problem; you must have obsolete code somewhere. (Yes, I know you said it was a clean checkout.) $ manjusri:svn/src/gnucash-git/src> grep -r "standard-reports balsheet-eg" --include="*.scm" . $ manjusri:svn/src/gnucash-git/src> What do you get? Regards, John Ralls _______________________________________________ gnucash-devel mailing list gnucash-devel@gnucash.org https://lists.gnucash.org/mailman/listinfo/gnucash-devel
