Further to this: you asked whether the problem occurs with level All. Interestingly, this option does result in the error occurring again.
However, when All is selected, the default report triggers the error with a different option number and a different number of iterations. This time, the erroneous value is indicated as '11', and it only occurs once. When 6 is selected, increasing the number of slices changes the number of times the error is iterated, although there isn't an apparent correlation between the slices shown and the number of errors. In other words, when I increase the number of slices by one (from the default 8 to 9), the added slice in the display is not at the seventh level, but the error is now repeated twice. The iterations do not change with the All setting; they remain at 1 regardless of the number of slices. I've looked at this more extensively now. I tried other "Slice-based" reports, under the assumption that their logic would cause similar results. I include my observed results below. I list the setting, followed by the error iteration in parentheses when the default settings are used, with only the depth value changed. In all cases, the All error was for option 11, and the 6 error was for option 7. Asset Chart (resulting tab is titled "Assets Over Time"): All (1) 6 (6) Asset Piechart (resulting tab is titled "Assets"): All (0) 6 (5) Liability Chart (resulting tab is titled "Liabilities Over Time"): All (1) 6 (2) Liability Piechart (resulting tab is titled "Liabilities"): All (1) 6 (2) It is interesting that the Asset Piechart didn't trigger any errors with the All setting. That was the only clean version. I will note that when I initially ran the Liability reports, I received no errors. This was because I didn't have any liabilities accounts at level 7. To verify this, I added dummy levels to one of the liabilities to reach level 7, and the errors started up. Further, I am confident that the number of iterations for the error is directly related to the number of level 6 accounts with level 7 children. When I add a parallel set of dummy accounts down to level 7 on another branch in Liabilities, the error iteration goes up by one. The mere presence of the level 7 account triggers errors. It didn't matter whether the dummy accounts had transactions in them, or whether the account was displayed in the resulting report. However, if the level 7 accounts are all empty, the error only triggers once. Adding a transaction to one of the dummy accounts increases the iteration to two, and adding to the other dummy also increases the iteration. This suggests that there is some relation between the number of seventh level slices to be displayed (as opposed to simply existing), but a base problem with that level on principle. David -------- Original Message -------- From: Adrien Monteleone <[email protected]> Sent: Sun Dec 06 15:22:14 EST 2020 To: [email protected] Subject: Re: [GNC] Error with Asset Chart report I have about a dozen or more level-6 asset accounts. I don't have anything greater than level-6. Can you reproduce if you try level-All? (there'd still be a bug in the level-6 option of course) Regards, Adrien On 12/6/20 2:17 PM, D. via gnucash-user wrote: > Adrien, > > Does your CoA have accounts deep enough to trigger level 6? I can trigger the > error consistently whenever I select a set of accounts that includes accounts > below the sixth, and then make it go away simply by selecting accounts that > don't range below that depth. _______________________________________________ gnucash-user mailing list [email protected] To update your subscription preferences or to unsubscribe: https://lists.gnucash.org/mailman/listinfo/gnucash-user If you are using Nabble or Gmane, please see https://wiki.gnucash.org/wiki/Mailing_Lists for more information. ----- Please remember to CC this list on all your replies. You can do this by using Reply-To-List or Reply-All. _______________________________________________ gnucash-user mailing list [email protected] To update your subscription preferences or to unsubscribe: https://lists.gnucash.org/mailman/listinfo/gnucash-user If you are using Nabble or Gmane, please see https://wiki.gnucash.org/wiki/Mailing_Lists for more information. ----- Please remember to CC this list on all your replies. You can do this by using Reply-To-List or Reply-All.
