So, I think brings up one of the slight frustrations I've always had with mmconfig..
If I have a cluster to which new nodes will eventually be added, OR, I have standard I always wish to apply, there is no way to say "all FUTURE" nodes need to have my defaults.. I just have to remember to extended the changes in as new nodes are brought into the cluster. Is there a way to accomplish this? Thanks Original Message From: [email protected] Sent: October 9, 2017 2:56 PM To: [email protected] Reply-to: [email protected] Subject: Re: [gpfsug-discuss] changing default configuration values Thanks! Good to know. On 10/6/17 11:06 PM, IBM Spectrum Scale wrote: > Hi Aaron, > > The default value applies to all nodes in the cluster. Thus changing it > will change all nodes in the cluster. You need to run mmchconfig to > customize the node override again. > > > Regards, The Spectrum Scale (GPFS) team > > ------------------------------------------------------------------------------------------------------------------ > If you feel that your question can benefit other users of Spectrum Scale > (GPFS), then please post it to the public IBM developerWroks Forum at > https://www.ibm.com/developerworks/community/forums/html/forum?id=11111111-0000-0000-0000-000000000479. > > > > If your query concerns a potential software error in Spectrum Scale > (GPFS) and you have an IBM software maintenance contract please contact > 1-800-237-5511 in the United States or your local IBM Service Center in > other countries. > > The forum is informally monitored as time permits and should not be used > for priority messages to the Spectrum Scale (GPFS) team. > > Inactive hide details for Aaron Knister ---10/06/2017 06:30:20 PM---Is > there a way to change the default value of a configuratiAaron Knister > ---10/06/2017 06:30:20 PM---Is there a way to change the default value > of a configuration option without overriding any overrid > > From: Aaron Knister <[email protected]> > To: gpfsug main discussion list <[email protected]> > Date: 10/06/2017 06:30 PM > Subject: [gpfsug-discuss] changing default configuration values > Sent by: [email protected] > > ------------------------------------------------------------------------ > > > > Is there a way to change the default value of a configuration option > without overriding any overrides in place? > > Take the following situation: > > - I set parameter foo=bar for all nodes (mmchconfig foo=bar) > - I set parameter foo to baz for a few nodes (mmchconfig foo=baz -N > n001,n002) > > Is there a way to then set the default value of foo to qux without > changing the value of foo for nodes n001 and n002? > > -Aaron > > -- > Aaron Knister > NASA Center for Climate Simulation (Code 606.2) > Goddard Space Flight Center > (301) 286-2776 > _______________________________________________ > gpfsug-discuss mailing list > gpfsug-discuss at spectrumscale.org > https://urldefense.proofpoint.com/v2/url?u=http-3A__gpfsug.org_mailman_listinfo_gpfsug-2Ddiscuss&d=DwICAg&c=jf_iaSHvJObTbx-siA1ZOg&r=IbxtjdkPAM2Sbon4Lbbi4w&m=PvuGmTBHKi7CNLU4X2GzUXkHzzezwTSrL4EdgwI0wrk&s=ma-IogZTBRL11_4zp2l8JqWmpHajoLXubAPSIS3K7GY&e= > > > > > > > _______________________________________________ > gpfsug-discuss mailing list > gpfsug-discuss at spectrumscale.org > http://gpfsug.org/mailman/listinfo/gpfsug-discuss > -- Aaron Knister NASA Center for Climate Simulation (Code 606.2) Goddard Space Flight Center (301) 286-2776 _______________________________________________ gpfsug-discuss mailing list gpfsug-discuss at spectrumscale.org http://gpfsug.org/mailman/listinfo/gpfsug-discuss _______________________________________________ gpfsug-discuss mailing list gpfsug-discuss at spectrumscale.org http://gpfsug.org/mailman/listinfo/gpfsug-discuss
