Would the PATH_NAME LIKE option work? Fred __________________________________________________ Fred Stock | IBM Pittsburgh Lab | 720-430-8821 [email protected]
From: "Jaime Pinto" <[email protected]> To: "gpfsug main discussion list" <[email protected]> Date: 04/18/2018 12:55 PM Subject: [gpfsug-discuss] mmapplypolicy on nested filesets ... Sent by: [email protected] A few months ago I asked about limits and dynamics of traversing depended .vs independent filesets on this forum. I used the information provided to make decisions and setup our new DSS based gpfs storage system. Now I have a problem I couldn't' yet figure out how to make it work: 'project' and 'scratch' are top *independent* filesets of the same file system. 'proj1', 'proj2' are dependent filesets nested under 'project' 'scra1', 'scra2' are dependent filesets nested under 'scratch' I would like to run a purging policy on all contents under 'scratch' (which includes 'scra1', 'scra2'), and TSM backup policies on all contents under 'project' (which includes 'proj1', 'proj2'). HOWEVER: When I run the purging policy on the whole gpfs device (with both 'project' and 'scratch' filesets) * if I use FOR FILESET('scratch') on the list rules, the 'scra1' and 'scra2' filesets under scratch are excluded (totally unexpected) * if I use FOR FILESET('scra1') I get error that scra1 is dependent fileset (Ok, that is expected) * if I use /*FOR FILESET('scratch')*/, all contents under 'project', 'proj1', 'proj2' are traversed as well, and I don't want that (it takes too much time) * if I use /*FOR FILESET('scratch')*/, and instead of the whole device I apply the policy to the /scratch mount point only, the policy still traverses all the content of 'project', 'proj1', 'proj2', which I don't want. (again, totally unexpected) QUESTION: How can I craft the syntax of the mmapplypolicy in combination with the RULE filters, so that I can traverse all the contents under the 'scratch' independent fileset, including the nested dependent filesets 'scra1','scra2', and NOT traverse the other independent filesets at all (since this takes too much time)? Thanks Jaime PS: FOR FILESET('scra*') does not work. ************************************ TELL US ABOUT YOUR SUCCESS STORIES https://urldefense.proofpoint.com/v2/url?u=http-3A__www.scinethpc.ca_testimonials&d=DwICAg&c=jf_iaSHvJObTbx-siA1ZOg&r=p_1XEUyoJ7-VJxF_w8h9gJh8_Wj0Pey73LCLLoxodpw&m=csxqKhhBsww-1H4lJlra9UtcoY0yG6PcOeV5jYf5pYo&s=tM9JZXsRNu6EEhoFlUuWvTLwMsqbDjfDj3NDZ6elACA&e= ************************************ --- Jaime Pinto - Storage Analyst SciNet HPC Consortium - Compute/Calcul Canada www.scinet.utoronto.ca - www.computecanada.ca University of Toronto 661 University Ave. (MaRS), Suite 1140 Toronto, ON, M5G1M1 P: 416-978-2755 C: 416-505-1477 ---------------------------------------------------------------- This message was sent using IMP at SciNet Consortium, University of Toronto. _______________________________________________ gpfsug-discuss mailing list gpfsug-discuss at spectrumscale.org https://urldefense.proofpoint.com/v2/url?u=http-3A__gpfsug.org_mailman_listinfo_gpfsug-2Ddiscuss&d=DwICAg&c=jf_iaSHvJObTbx-siA1ZOg&r=p_1XEUyoJ7-VJxF_w8h9gJh8_Wj0Pey73LCLLoxodpw&m=csxqKhhBsww-1H4lJlra9UtcoY0yG6PcOeV5jYf5pYo&s=V6u0XsNxHj4Mp-mu7hCZKv1AD3_GYqU-4KZzvMSQ_MQ&e=
_______________________________________________ gpfsug-discuss mailing list gpfsug-discuss at spectrumscale.org http://gpfsug.org/mailman/listinfo/gpfsug-discuss
