ok thanks. guess i should change both rates so it will work otherwise, i will always have this issue lol.
On Jan 26, 2010, at 10:21 PM, Steve Jacobson wrote: > From what I can tell, what you describe is normal. If you check Eloquence to > remember speech parameters and then > you push the button to use current parameters, that will cause the current > parameters to be remembered when you > return to Eloquence. If you now switch to another synthesizer for which > speech parameters have not been > remembered, that synthesizer will start out using the parameters you had in > effect just before you switched to that > synthesizer. It would have no choice because there are none remembered. If > you want Dec-talk to have one set of > settings all the time and Eloquence another, you need to have both remember > their settings. Synthesizers that do not > have settings remembered will always start out with the settings previously > in effect. > > This is all obvious once it is understood, but I struggled with it for a bit > of time before it made sense. Hang in there and > try setting and remembering settings for each synthesizer you wish to have > its own settings. > > Best regards, > > Steve Jacobson > > On Tue, 26 Jan 2010 22:05:38 -0500, Brandon Misch wrote: > >> Hey all. i tried the suggestions that rual made and no matter which synth i >> chose, the rates were the same. i went to my > first synth wich was eloquence checked the checkbox for use specified speech > parameters thinking that this would > make the current synth honor the settings but when i switched to my other > synth, those settings i made for eloquence > also went with it so my dectalk was also faster when i only wanted eloquence > that way, so i went back and checked > the engine specific parameters checkbox and that made no difference. then, > when i was back using eloquence, i hit the > button that was the set speech parameters to current. and the synth settings > still didn't stick. a friend of mine tested this > by checking the speech parameters checkbox for eloquence but not for dectalk, > and the settings both were the same > for both synths. rate 50 for all voices when i only wanted eloquence that > fast. this friend is using windows xp and i am > using windows 7 and we both have admin wrights. and he told me this used to > wrok wright in 4.5 and higher. even in > the manual it talks about having the speech parameters checkbox checked and > entering on the set speech parameters > to current button would save the settings for that synth and that synth only. > >> If you reply to this message it will be delivered to the original >> sender only. If your reply would benefit others on the list and >> your message is related to GW Micro, then please consider sending >> your message to [email protected] so the entire list will receive it. > >> All GW-Info messages are archived at http://www.gwmicro.com/gwinfo, and can >> be searched through and sorted > using the search >> form at the bottom of the page. > >> If you wish to unsubscribe from this list, visit: > >> http://www.gwmicro.com/listserv > > > > > > If you reply to this message it will be delivered to the original > sender only. If your reply would benefit others on the list and > your message is related to GW Micro, then please consider sending > your message to [email protected] so the entire list will receive it. > > All GW-Info messages are archived at http://www.gwmicro.com/gwinfo, and can > be searched through and sorted using the search > form at the bottom of the page. > > If you wish to unsubscribe from this list, visit: > > http://www.gwmicro.com/listserv > If you reply to this message it will be delivered to the original sender only. If your reply would benefit others on the list and your message is related to GW Micro, then please consider sending your message to [email protected] so the entire list will receive it. All GW-Info messages are archived at http://www.gwmicro.com/gwinfo, and can be searched through and sorted using the search form at the bottom of the page. If you wish to unsubscribe from this list, visit: http://www.gwmicro.com/listserv
