Thanks Tom, good point. Kevin Huber On 1/27/14, Tom Kingston <[email protected]> wrote: > Just a note. When you hit Control-O to open a set file you're in a combo > edit box. So if you know the file name you can just type it in (without > having to delete the currently shown set file name) and hit enter to > load it. Then just hit the title bar hot key (Control-Shift-T) to make > sure. The Window-Eyes title bar will show the currently loaded set file > followed by the currently associated set file; the latter of which will > be Default.set if no set file is associated. > > Hth, > Tom > > > On 1/27/2014 10:25 AM, Kevin Huber wrote: >> Hi Matt: >> First, welcome to this list, you will find that the members of this >> list are happy to answer any question that you have about Window-eyes >> no matter what it is. So I will attempt to answer this one for you. >> >> First, there is a set file called "silent.set which you will have to >> open and then you will have to associate this file with Kurzweil 1000. >> I will explain both of these procedures step by step. >> First, you will have to enable the advanced options as follows: >> 1. go to the Window-eyes control panel by pressing control-backslash. >> 2.Press alt-h to get into the Help menu. >> 3. Arrow down to "show advanced options" and if it is not checked, >> press the enter key to check it. >> >> Opening the Silent.set set file: >> 1. Make sure that you have Kurzweil 1000 open. >> 2. Go into the Window-eyes control panel by pressing control-backslash. >> 3. Press control-o to open the Open File dialog. >> 4. Press Shift-Tab once or twice, depending on your operating system, >> until you get to the list of set files. >> 5. Press the letter S until you get to Silent.set, then press the Enter >> key. >> >> Now we have to associate the Silent.set setfile with Kurzweil 1000 so >> that whenever you open Kurzweil 1000, the Silent.set file will >> automatically open, causing Window-eyes to remain silent while >> Kurzwiel 1000 is opened and when you close Kurzweil 1000,Window-eyes >> will go bac to working normally. >> Perform the following steps: >> 1. Go to the Window-eyes control panel if you are not already there. >> 2. Press the letter a to get to Association in the tree view. >> 3. Press the right arrow key to open the tree view. >> 4. Press the down arrow key to get to Current Association. >> 5. Press the tab key and you should here the name of the set file >> "silent.set". >> 6. Press the tab key again and you should get to a series of radio >> buttons. The one that is checked is "associate by class". The other >> two are "by title" and "none". The best thing to do is to check >> "associate by class". >> 7. Press the tab key once more to get to the Save And Associate button >> and press the spacebar. >> 8. Press the tab key again to get to the Save button and press the >> spacebar. >> Now, Window-eyes should behave properly in Kurzweil 1000, and you will >> not have to repeat the above steps. >> I hope this helps. >> Kevin Huber >> >> On 1/26/14, Matt Shaw <[email protected]> wrote: >>> Hi all. I'd first like to introduce myself. My name is Matthew and I >>> have >>> just recently begun using window eyes and am very impressed with it so >>> far. >>> However, I do have a question. I'd like to know how to put window eyes >>> to >>> sleep for certain applications. For instance, I use Kurzweil 1000 for >>> scanning documents, reading certain materials, etc. I'd like to be able >>> to >>> put window eyes to sleep while Kurzweil is loaded since it is self >>> voicing, >>> but have window eyes immediately resume normal operation once Kurzweil >>> is >>> closed or I switch to another window. Any assistance on this matter >>> would >>> be >>> greatly appreciated. >>> >>> >>> If you reply to this message it will be delivered to the original sender >>> only. If your reply would benefit others on the list and your message is >>> related to GW Micro, then please consider sending your message to >>> [email protected] so the entire list will receive it. >>> >>> GW-Info messages are archived at http://www.gwmicro.com/gwinfo. You can >>> manage your list subscription at http://www.gwmicro.com/listserv. >> If you reply to this message it will be delivered to the original sender >> only. If your reply would benefit others on the list and your message is >> related to GW Micro, then please consider sending your message to >> [email protected] so the entire list will receive it. >> >> GW-Info messages are archived at http://www.gwmicro.com/gwinfo. You can >> manage your list subscription at http://www.gwmicro.com/listserv. >> >> > If you reply to this message it will be delivered to the original sender > only. If your reply would benefit others on the list and your message is > related to GW Micro, then please consider sending your message to > [email protected] so the entire list will receive it. > > GW-Info messages are archived at http://www.gwmicro.com/gwinfo. You can > manage your list subscription at http://www.gwmicro.com/listserv. > > If you reply to this message it will be delivered to the original sender only. If your reply would benefit others on the list and your message is related to GW Micro, then please consider sending your message to [email protected] so the entire list will receive it.
GW-Info messages are archived at http://www.gwmicro.com/gwinfo. You can manage your list subscription at http://www.gwmicro.com/listserv.
