I agree with the suggestion of the router change but with the standard firmware u can do what u need but u have to assign ur server the first ip address -- original message -- Subject: Re: [hlds] Server isn't being shown on master list? From: "OoksServer" <[EMAIL PROTECTED]> Date: 10th August 2005 2:07:44 pm
Your problem is that you have not assigned static IP address to the macid of your nic in you server, so when there is a power loss or probably when you reboot and/or shut off the server, it comes back up with a different IP address. I'm not sure if your router will let you make static ip/macid assignments. D-Link routers are inherintely evil, and IIRC the reviews I read on their gaming router more or less decided that they were a waste of money. Chuck it in the trash, get a WRT54G, download Talisman firmeware from Sveasoft so you can make static IP/MACID assignments, and your router problems will be a thing of the past :-) BTW, you don't need to forward all of those ports. Most of them are ports at the remote, not ports on your end and forwarding them accomplishes nothing because they aren't used locally. ----- Original Message ----- From: "[DMA]RocketUSA" <[EMAIL PROTECTED]> To: <[email protected]> Sent: Wednesday, August 10, 2005 12:37 PM Subject: RE: [hlds] Server isn't being shown on master list? > WOW! Most of this subject is Greek to me with what has been stated from > everyone. I only have a problem with my server being shown on the list > after > a power failure or have to shut down my entire network, but, never have a > problem fixing it. > My setup: SURFboard4200 modem, D-Link DGL-4300 gaming router. > Computers: Mine, Hers, and the server. (CS 1.6) > When it doesn't show, I just go into the routers advanced settings under > gaming and put in the servers new LAN IP. (the LAN IP's change when > there's > a total network shut-down) Of course all my ports are already there, and > that's it. Once the router is rebooted it shows up. > PORTS: TCP: 5273, 7002, 27020 - 27040 > UDP: 1200, 1300, 27000 - 27015 > > I don't know if this will help you, but, this is my first post in here. > > > > > -----Original Message----- > From: [EMAIL PROTECTED] > [mailto:[EMAIL PROTECTED] On Behalf Of Ook > Sent: Wednesday, August 10, 2005 1:12 AM > To: [email protected] > Subject: Re: [hlds] Server isn't being shown on master list? > > No, you misunderstand what I'm saying. Put modem in bridge mode. Run cat5 > from modem to WRT54G (or equivalent). Setup WRT54G for PPPOE/A, or > whatever > your ISP requires, including your userid/password. The Zoom modem in > bridge > mode for all practical purposes becomes invisible. The WRT54G wan IP is > the > ip your ISP assigns you. It becomes your router, it has the dhcp server in > it. All other devices on network work as they always have. It is as if you > were using that as your modem. Use it's built in 4 port switch, or run > cat5 > to another hub/switch/wap, etc. It also has builtin wirelessb/g. > > The above scenario assumes your ISP supports running your modem in gateway > mode, your modem actually does this, and you have a router of some sort > that > can handle the pppoe/a/etc from your ISP. Mine does, this is what I do, > and > it works very well. > > In the above example, bridge mode turns control of the network over to the > WRT54G, which has a router and 4 port switch and dhcp server built in. > This > is a good thing. > > > > _______________________________________________ > To unsubscribe, edit your list preferences, or view the list archives, > please visit: > http://list.valvesoftware.com/mailman/listinfo/hlds _______________________________________________ To unsubscribe, edit your list preferences, or view the list archives, please visit: http://list.valvesoftware.com/mailman/listinfo/hlds _______________________________________________ To unsubscribe, edit your list preferences, or view the list archives, please visit: http://list.valvesoftware.com/mailman/listinfo/hlds
