Hi Zaki, Looks like something went wrong with your CUPS installation, either the "tmp" directory doesn't exist or it doesn't have right permissions. This is from the error_log file:
D [05/Nov/2006:10:10:05 +0100] [Job 8] ESP Ghostscript 815.01: **** Could not open temporary file /var/spool/cups/tmp/gs_derRSW D [05/Nov/2006:10:10:05 +0100] [Job 8] ESP Ghostscript 815.01: Could not open the scratch file /var/spool/cups/tmp/gs_derRSW. D [05/Nov/2006:10:10:05 +0100] [Job 8] **** Unable to open the initial device, quitting. The permissions on /var/spool/cups/tmp should be something like: drwxrwx--T 2 root lp ... Raghu -----Original Message----- From: Zaki Mohzani [mailto:[EMAIL PROTECTED] Sent: Saturday, November 04, 2006 8:21 AM To: Cauligi, Raghothama S; hplip-help@lists.sourceforge.net Subject: Re: [Hplip-help] HP PSC 1410 Test page print problem i've attached a part of the error_log, and black catridge in hp-toolbox says "Low" not empty, but there is nothing in the bars underneath it. On 11/2/06, Cauligi, Raghothama S <[EMAIL PROTECTED]> wrote: > Set LogLevel to debug in /etc/cupsd.conf (or the equivalent cups > config file), restart cups (/etc/init.d/cups restart) Print the test > page again and check the cups log file > (/var/log/cups/error_log) > Also, check your printer configuration page, perhaps you have it set > to grayscale with black cartridge and black cartridge is empty or > close to it? > Raghu > > -----Original Message----- > From: [EMAIL PROTECTED] > [mailto:[EMAIL PROTECTED] On Behalf Of Zaki > Sent: Thursday, November 02, 2006 12:21 PM > To: hplip-help@lists.sourceforge.net > Subject: [Hplip-help] HP PSC 1410 Test page print problem > > Hi there, > > I've searched around for my problem, the closest I've found is a post > by Jyri Turkia on 2006-07-10 23:18:20 , titled "HP PSC 1410 won't print". > > Similar problem, I've had setup the print numerously, and this last > time, I am very sure I got the installation right. hp-setup ran fine, > hp-toolbox shows the info about the printer BUT the test page just > wouldn't print. KDE shows vaguely 'Error', with job-state='0x6'. > > Possibilites: > 1. It is shown in toolbox, Code: 1501 black print cartridge is low on > ink. Still, shouldn't still print? (just assuming) 2. :) I just don't > know. > > My log for /var/log/messages when I print is empty. > My system is a converted knoppix to debian. > > Thanks. > > The output: > [EMAIL PROTECTED] hp-check > > HP Linux Imaging and Printing System (ver. 1.6.10) Dependency/Version > Check Utility ver. 4.0 > > Copyright (c) 2003-6 Hewlett-Packard Development Company, LP This > software comes with ABSOLUTELY NO WARRANTY. > This is free software, and you are welcome to distribute it under > certain conditions. See COPYING file for more details. > > > --------------- > | SYSTEM INFO | > --------------- > > Basic system info (uname -a): > --> Linux Knoppix 2.6.17 #4 SMP PREEMPT Wed May 10 13:53:45 CEST > 2006 i686 GNU/Linux > > Detected distro (/etc/issue): > --> debian 0.0 > > Detected distro (lsb_release): > --> Debian testing (etch) > > Currently installed version... > --> OK, HPLIP 1.6.10 currently installed in '/usr/share/hplip'. > > Current contents of '/etc/hp/hplip.conf' file: > # hplip.conf > > [hpiod] > # port=0 (dynamic IP port) > port=2208 (IANA IP port) > [hpssd] > # port=0 (dynamic IP port) > port=2207 (IANA IP port) > > [hplip] > version=1.6.10 > jdprobe=0 > > [dirs] > home=/usr/share/hplip > run=/var/run > ppd=/usr/share/ppd/HP > doc=/usr/share/doc/hplip-1.6.10 > > # Following values are determined at configure time and cannot be > changed. > [configure] > network-build=1 > pp-build=1 > gui-build=1 > scanner-build=1 > fax-build=1 > internal-tag=1.6.10.11 > > > HPLIP running? > --> Yes, HPLIP is running (OK). > > HPOJ running? > --> No, HPOJ is not running (OK). > > Checking Python version... > --> OK, version 2.4.4 installed > > ---------------- > | DEPENDENCIES | > ---------------- > > > Checking for dependency 'libcrypto (libcrypto - OpenSSL cryptographic > library)'... > --> OK, found. > > Checking for dependency 'gcc (gcc - GNU Project C and C++ Compiler)'... > --> OK, found. > > Checking for dependency 'sane (SANE - Scanning library)'... > --> OK, found. > > Checking for dependency 'gs (GhostScript - PostScript and PDF language > interpreter and previewer)'... > --> OK, found. > > Checking for dependency 'libjpeg (libjpeg - JPEG library)'... > --> OK, found. > > Checking for dependency 'libpthread (libpthread - POSIX threads > library)'... > --> OK, found. > > Checking for dependency 'make (make - GNU make utility to maintain > groups of programs)'... > --> OK, found. > > Checking for dependency 'python-devel (python-devel - Python > development files)'... > --> OK, found. > > Checking for dependency 'reportlab (Reportlab - PDF library for > Python)'... > error: Not found! > This is an OPTIONAL dependency. > > Checking for dependency 'pyqt (PyQt - Qt interface for Python)'... > --> OK, found. > > Checking for dependency 'cups-devel (cups-devel- Common Unix Printing > System development files)'... > --> OK, found. > > Checking for dependency 'ppdev (ppdev - Parallel port support kernel > module.)'... > --> OK, found. > > Checking for dependency 'libusb (libusb - USB library)'... > --> OK, found. > > Checking for dependency 'scanimage (scanimage - Shell scanning > program)'... > --> OK, found. > > Checking for dependency 'libnetsnmp-devel (libnetsnmp-devel - SNMP > networking library development files)'... > --> OK, found. > > Checking for dependency 'python2x (Python 2.2 or greater - Python > programming language)'... > --> OK, found. > > Checking for dependency 'lsb (LSB - Linux Standard Base support)'... > --> OK, found. > > Checking for dependency 'xsane (xsane - Graphical scanner frontend for > SANE)'... > --> OK, found. > > Checking for dependency 'cups (cups - Common Unix Printing System)'... > --> OK, found. > > Checking for dependency 'python23 (Python 2.3 or greater - Required > for fax functionality)'... > --> OK, found. > > > ---------------------- > | INSTALLED PRINTERS | > ---------------------- > > > PSC_1400 > -------- > Device URI: hp:/usb/PSC_1400_series?serial=MY5BGCC1NJ04BM > Installed in HPLIP? Yes > PPD: /etc/cups/ppd/PSC_1400.ppd > PPD Description: HP PSC 1400 Foomatic/hpijs (recommended) > > Printer status: > printer PSC_1400 is idle. enabled since Thu Nov 2 18:44:32 2006 > ready to print > > > > ---------------------- > | SANE CONFIGURATION | > ---------------------- > > 'hpaio' in /etc/sane.d/dll.conf'... > --> OK, found. SANE backend 'hpaio' is not properly set up. > > Checking output of 'scanimage -L'... > device `hpaio:/usb/PSC_1400_series?serial=MY5BGCC1NJ04BM' is a hp > PSC_1400_series multi-function peripheral > > > --------------------- > | PYTHON EXTENSIONS | > --------------------- > > Checking 'cupsext' CUPS extension... > --> OK, found. > > Checking 'pcardext' Photocard extension... > --> OK, found. > > > %d errors were detected. > Please refer to the installation instructions at: > http://hplip.sourceforge.net/install/index.html > > ---------------------------------------------------------------------- > -- > - > Using Tomcat but need to do more? Need to support web services, > security? > Get stuff done quickly with pre-integrated technology to make your job > easier Download IBM WebSphere Application Server v.1.0.1 based on > Apache Geronimo > http://sel.as-us.falkag.net/sel?cmd=lnk&kid=120709&bid=263057&dat=1216 > 42 _______________________________________________ > HPLIP-Help mailing list > HPLIP-Help@lists.sourceforge.net > https://lists.sourceforge.net/lists/listinfo/hplip-help > ------------------------------------------------------------------------- Using Tomcat but need to do more? Need to support web services, security? Get stuff done quickly with pre-integrated technology to make your job easier Download IBM WebSphere Application Server v.1.0.1 based on Apache Geronimo http://sel.as-us.falkag.net/sel?cmd=lnk&kid=120709&bid=263057&dat=121642 _______________________________________________ HPLIP-Help mailing list HPLIP-Help@lists.sourceforge.net https://lists.sourceforge.net/lists/listinfo/hplip-help
