Dumping the register values before and after every transaction was useful during driver development but now it's only spamming the log.
Signed-off-by: Jean Delvare <[EMAIL PROTECTED]> --- This patch and the 3 that follow, apply on top of 2.6.26-rc6 + my i2c tree. If you want to test them, it's probably easier to pick my tar'ed i2c tree at: http://khali.linux-fr.org/devel/linux-2.6/ drivers/i2c/busses/i2c-i801.c | 18 ------------------ 1 file changed, 18 deletions(-) --- linux-2.6.26-rc5.orig/drivers/i2c/busses/i2c-i801.c 2008-06-08 20:36:31.000000000 +0200 +++ linux-2.6.26-rc5/drivers/i2c/busses/i2c-i801.c 2008-06-14 17:13:11.000000000 +0200 @@ -139,11 +139,6 @@ static int i801_transaction(int xact) int result = 0; int timeout = 0; - dev_dbg(&I801_dev->dev, "Transaction (pre): CNT=%02x, CMD=%02x, " - "ADD=%02x, DAT0=%02x, DAT1=%02x\n", inb_p(SMBHSTCNT), - inb_p(SMBHSTCMD), inb_p(SMBHSTADD), inb_p(SMBHSTDAT0), - inb_p(SMBHSTDAT1)); - /* Make sure the SMBus host is ready to start transmitting */ /* 0x1f = Failed, Bus_Err, Dev_Err, Intr, Host_Busy */ if ((temp = (0x1f & inb_p(SMBHSTSTS))) != 0x00) { @@ -203,10 +198,6 @@ static int i801_transaction(int xact) dev_dbg(&I801_dev->dev, "Failed reset at end of transaction " "(%02x)\n", temp); } - dev_dbg(&I801_dev->dev, "Transaction (post): CNT=%02x, CMD=%02x, " - "ADD=%02x, DAT0=%02x, DAT1=%02x\n", inb_p(SMBHSTCNT), - inb_p(SMBHSTCMD), inb_p(SMBHSTADD), inb_p(SMBHSTDAT0), - inb_p(SMBHSTDAT1)); return result; } @@ -294,11 +285,6 @@ static int i801_block_transaction_byte_b } outb_p(smbcmd | ENABLE_INT9, SMBHSTCNT); - dev_dbg(&I801_dev->dev, "Block (pre %d): CNT=%02x, CMD=%02x, " - "ADD=%02x, DAT0=%02x, DAT1=%02x, BLKDAT=%02x\n", i, - inb_p(SMBHSTCNT), inb_p(SMBHSTCMD), inb_p(SMBHSTADD), - inb_p(SMBHSTDAT0), inb_p(SMBHSTDAT1), inb_p(SMBBLKDAT)); - /* Make sure the SMBus host is ready to start transmitting */ temp = inb_p(SMBHSTSTS); if (i == 1) { @@ -382,10 +368,6 @@ static int i801_block_transaction_byte_b "Bad status (%02x) at end of transaction\n", temp); } - dev_dbg(&I801_dev->dev, "Block (post %d): CNT=%02x, CMD=%02x, " - "ADD=%02x, DAT0=%02x, DAT1=%02x, BLKDAT=%02x\n", i, - inb_p(SMBHSTCNT), inb_p(SMBHSTCMD), inb_p(SMBHSTADD), - inb_p(SMBHSTDAT0), inb_p(SMBHSTDAT1), inb_p(SMBBLKDAT)); if (result < 0) return result; -- Jean Delvare _______________________________________________ i2c mailing list [email protected] http://lists.lm-sensors.org/mailman/listinfo/i2c
