Add fast_mode option to i2c_pxa_platform_data and use it to set the ICR_FM bit
appropriately when i2c_pxa_reset is called. Parameter called fast_mode rather
than frequency as this driver is also used for the i2c_pxa_pwr bus which has
different normal and fast frequencies.
Signed-off-by: Jonathan Cameron <[EMAIL PROTECTED]>
---
drivers/i2c/busses/i2c-pxa.c | 4 +++-
include/asm-arm/arch-pxa/i2c.h | 1 +
include/asm-arm/arch-pxa/pxa-regs.h | 1 +
3 files changed, 5 insertions(+), 1 deletion(-)
--- a/include/asm-arm/arch-pxa/pxa-regs.h 2008-06-30 20:06:02.000000000
+0100
+++ b/include/asm-arm/arch-pxa/pxa-regs.h 2008-07-02 14:03:19.000000000
+0100
@@ -448,6 +448,7 @@
#define ICR_ALDIE (1 << 12) /* enable arbitration interrupt */
#define ICR_SADIE (1 << 13) /* slave address detected int enable
*/
#define ICR_UR (1 << 14) /* unit reset */
+#define ICR_FM (1 << 15) /* fast mode */
#define ISR_RWM (1 << 0) /* read/write mode */
#define ISR_ACKNAK (1 << 1) /* ack/nak status */
--- a/include/asm-arm/arch-pxa/i2c.h 2008-06-30 20:04:02.000000000 +0100
+++ b/include/asm-arm/arch-pxa/i2c.h 2008-07-02 13:59:59.000000000 +0100
@@ -66,6 +66,7 @@ struct i2c_pxa_platform_data {
struct i2c_slave_client *slave;
unsigned int class;
int use_pio;
+ int fast_mode;
};
extern void pxa_set_i2c_info(struct i2c_pxa_platform_data *info);
--- a/drivers/i2c/busses/i2c-pxa.c 2008-06-30 20:05:51.000000000 +0100
+++ b/drivers/i2c/busses/i2c-pxa.c 2008-07-02 15:50:31.000000000 +0100
@@ -67,6 +67,7 @@ struct pxa_i2c {
int irq;
int use_pio;
+ int fast_mode;
};
#define _IBMR(i2c) ((i2c)->reg_base + 0)
@@ -365,7 +366,7 @@ static void i2c_pxa_reset(struct pxa_i2c
writel(i2c->slave_addr, _ISAR(i2c));
/* set control register values */
- writel(I2C_ICR_INIT, _ICR(i2c));
+ writel(I2C_ICR_INIT | (i2c->fast_mode ? ICR_FM : 0), _ICR(i2c));
#ifdef CONFIG_I2C_PXA_SLAVE
dev_info(&i2c->adap.dev, "Enabling slave mode\n");
@@ -1041,6 +1042,7 @@ static int i2c_pxa_probe(struct platform
if (plat) {
i2c->adap.class = plat->class;
i2c->use_pio = plat->use_pio;
+ i2c->fast_mode = plat->fast_mode;
}
if (i2c->use_pio) {
_______________________________________________
i2c mailing list
[email protected]
http://lists.lm-sensors.org/mailman/listinfo/i2c
