Henrique de Moraes Holschuh <h...@hmh.eng.br> writes:
> On Sat, 14 Nov 2009, Ferenc Wagner wrote:
>> thinkpad_acpi: ThinkPad BIOS 1WET90WW (2.10 ), EC 1VHT28WW-1.04
>> thinkpad_acpi: IBM ThinkPad R50e, model 1834S5G
>
> ...
>
>> Actually, this is the only mode that does NOT work; both 1 and 3 work
>> instead. Hope it's useful.
>
> Yes, it is. Can you give me the output of lspci for your ThinkPad, please?
Certainly, please find it attached.
> Also, while we're at it, I'd appreciate if you could send me by private
> email the full output of acpidump, and the output of dmidecode (please mask
> out any serial numbers and UUIDs).
No problem. I'm somewhat surprised that the current output of acpidump
differs from what's attached to
http://bugs.freedesktop.org/show_bug.cgi?id=22126, does that depend on
the time of the boot, or what?
>> I've got two -- probably not particularly useful -- notes as well:
>>
>> 1. The thinkpad_acpi module has lots of parameters, but no
>> /sys/modules/thinkpad_acpi/parameters directory. Even if no
>> parameters are changeable in runtime, this is unusual.
>
> If you feel it would be useful to have the read-only parameters displayed
> there, I can update the module to have them show up.
Well, it would have been convenient yesterday, but in the end I found
what I was after in dmesg (current brightness_mode). But I guess
everything isn't output there. On the other hand, I've never felt the
need before, and probably won't again, after this warning disappears.
>> 2. While removing and reloading the module trying the different modes, I
>> managed to reach the state that the /proc/acpi/ibm directory is
>> created, but left empty by the module. I'm unable to reproduce it
>> now, but it wasn't the first time, I also got here a couple of months
>> ago playing with the module. Then I postponed sending in this report
>> for this reason: I hate such things. :) Maybe my PWD was
>> /proc/acpi/ibm when I (tried to) remove the module, maybe not...
>
> Well, that would be a bug somewhere else in the kernel, I think, unless I am
> missing declaring an owner somewhere. I will look into it.
Thanks. I'll try to reproduce it meanwhile.
--
Regards,
Feri.
00:00.0 Host bridge: Intel Corporation 82852/82855 GM/GME/PM/GMV Processor to
I/O Controller (rev 02)
Subsystem: IBM ThinkPad R50e
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort+ >SERR- <PERR- INTx-
Latency: 0
Region 0: Memory at <unassigned> (32-bit, prefetchable)
Capabilities: [40] Vendor Specific Information <?>
Kernel driver in use: agpgart-intel
Kernel modules: intel-agp
00:00.1 System peripheral: Intel Corporation 82852/82855 GM/GME/PM/GMV
Processor to I/O Controller (rev 02)
Subsystem: IBM ThinkPad R50e
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
00:00.3 System peripheral: Intel Corporation 82852/82855 GM/GME/PM/GMV
Processor to I/O Controller (rev 02)
Subsystem: IBM ThinkPad R50e
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
00:02.0 VGA compatible controller: Intel Corporation 82852/855GM Integrated
Graphics Device (rev 02) (prog-if 00 [VGA controller])
Subsystem: IBM ThinkPad R50e
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx+
Latency: 0
Interrupt: pin A routed to IRQ 11
Region 0: Memory at e0000000 (32-bit, prefetchable) [size=128M]
Region 1: Memory at d0000000 (32-bit, non-prefetchable) [size=512K]
Region 2: I/O ports at 1800 [size=8]
Capabilities: [d0] Power Management version 1
Flags: PMEClk- DSI+ D1+ D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:02.1 Display controller: Intel Corporation 82852/855GM Integrated Graphics
Device (rev 02)
Subsystem: IBM ThinkPad R50e
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Region 0: Memory at e8000000 (32-bit, prefetchable) [size=128M]
Region 1: Memory at d0080000 (32-bit, non-prefetchable) [size=512K]
Capabilities: [d0] Power Management version 1
Flags: PMEClk- DSI+ D1+ D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:1d.0 USB Controller: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M)
USB UHCI Controller #1 (rev 01) (prog-if 00 [UHCI])
Subsystem: IBM ThinkPad
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 11
Region 4: I/O ports at 1820 [size=32]
Kernel driver in use: uhci_hcd
Kernel modules: uhci-hcd
00:1d.1 USB Controller: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M)
USB UHCI Controller #2 (rev 01) (prog-if 00 [UHCI])
Subsystem: IBM ThinkPad
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 11
Region 4: I/O ports at 1840 [size=32]
Kernel driver in use: uhci_hcd
Kernel modules: uhci-hcd
00:1d.2 USB Controller: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M)
USB UHCI Controller #3 (rev 01) (prog-if 00 [UHCI])
Subsystem: IBM ThinkPad
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin C routed to IRQ 11
Region 4: I/O ports at 1860 [size=32]
Kernel driver in use: uhci_hcd
Kernel modules: uhci-hcd
00:1d.7 USB Controller: Intel Corporation 82801DB/DBM (ICH4/ICH4-M) USB2 EHCI
Controller (rev 01) (prog-if 20 [EHCI])
Subsystem: IBM ThinkPad
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin D routed to IRQ 11
Region 0: Memory at d0100000 (32-bit, non-prefetchable) [size=1K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME+
Capabilities: [58] Debug port: BAR=1 offset=0080
Kernel driver in use: ehci_hcd
Kernel modules: ehci-hcd
00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev 81) (prog-if
00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR+ INTx-
Latency: 0
Bus: primary=00, secondary=02, subordinate=05, sec-latency=64
I/O behind bridge: 00003000-00007fff
Memory behind bridge: d0200000-dfffffff
Prefetchable memory behind bridge: f0000000-f7ffffff
Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
00:1f.0 ISA bridge: Intel Corporation 82801DBM (ICH4-M) LPC Interface Bridge
(rev 01)
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Kernel modules: intel-rng, iTCO_wdt
00:1f.1 IDE interface: Intel Corporation 82801DBM (ICH4-M) IDE Controller (rev
01) (prog-if 8a [Master SecP PriP])
Subsystem: IBM ThinkPad
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 11
Region 0: I/O ports at 01f0 [size=8]
Region 1: I/O ports at 03f4 [size=1]
Region 2: I/O ports at 0170 [size=8]
Region 3: I/O ports at 0374 [size=1]
Region 4: I/O ports at 1810 [size=16]
Region 5: Memory at 20000000 (32-bit, non-prefetchable) [size=1K]
Kernel driver in use: PIIX_IDE
Kernel modules: piix
00:1f.3 SMBus: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) SMBus
Controller (rev 01)
Subsystem: IBM ThinkPad
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin B routed to IRQ 11
Region 4: I/O ports at 1880 [size=32]
Kernel driver in use: i801_smbus
Kernel modules: i2c-i801
00:1f.5 Multimedia audio controller: Intel Corporation 82801DB/DBL/DBM
(ICH4/ICH4-L/ICH4-M) AC'97 Audio Controller (rev 01)
Subsystem: IBM Thinkpad R50e model 1634
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 11
Region 0: I/O ports at 1c00 [size=256]
Region 1: I/O ports at 18c0 [size=64]
Region 2: Memory at d0100c00 (32-bit, non-prefetchable) [size=512]
Region 3: Memory at d0100800 (32-bit, non-prefetchable) [size=256]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: Intel ICH
Kernel modules: snd-intel8x0
00:1f.6 Modem: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) AC'97
Modem Controller (rev 01) (prog-if 00 [Generic])
Subsystem: IBM ThinkPad R50e
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin B routed to IRQ 11
Region 0: I/O ports at 2400 [size=256]
Region 1: I/O ports at 2000 [size=128]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
02:00.0 CardBus bridge: Texas Instruments PCI1510 PC card Cardbus Controller
Subsystem: IBM ThinkPad R50e
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64, Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 11
Region 0: Memory at b0000000 (32-bit, non-prefetchable) [size=4K]
Bus: primary=02, secondary=03, subordinate=04, sec-latency=176
Memory window 0: f0000000-f3fff000 (prefetchable)
Memory window 1: d4000000-d7fff000 (prefetchable)
I/O window 0: 00003000-000030ff
I/O window 1: 00003400-000034ff
BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset+ 16bInt+ PostWrite-
16-bit legacy interface ports at 0001
02:02.0 Network controller: Intel Corporation PRO/Wireless 2200BG [Calexico2]
Network Connection (rev 05)
Subsystem: Intel Corporation IBM ThinkPad R50e
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64 (750ns min, 6000ns max), Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 11
Region 0: Memory at d0200000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=1 PME-
Kernel driver in use: ipw2200
Kernel modules: ipw2200
02:08.0 Ethernet controller: Intel Corporation 82801DB PRO/100 VE (MOB)
Ethernet Controller (rev 81)
Subsystem: IBM ThinkPad R40
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 66 (2000ns min, 14000ns max), Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 11
Region 0: Memory at d0201000 (32-bit, non-prefetchable) [size=4K]
Region 1: I/O ports at 7000 [size=64]
Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA
PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=2 PME-
Kernel driver in use: e100
Kernel modules: e100
00:00.0 0600: 8086:3580 (rev 02)
00:00.1 0880: 8086:3584 (rev 02)
00:00.3 0880: 8086:3585 (rev 02)
00:02.0 0300: 8086:3582 (rev 02)
00:02.1 0380: 8086:3582 (rev 02)
00:1d.0 0c03: 8086:24c2 (rev 01)
00:1d.1 0c03: 8086:24c4 (rev 01)
00:1d.2 0c03: 8086:24c7 (rev 01)
00:1d.7 0c03: 8086:24cd (rev 01)
00:1e.0 0604: 8086:2448 (rev 81)
00:1f.0 0601: 8086:24cc (rev 01)
00:1f.1 0101: 8086:24ca (rev 01)
00:1f.3 0c05: 8086:24c3 (rev 01)
00:1f.5 0401: 8086:24c5 (rev 01)
00:1f.6 0703: 8086:24c6 (rev 01)
02:00.0 0607: 104c:ac56
02:02.0 0280: 8086:4220 (rev 05)
02:08.0 0200: 8086:103d (rev 81)
------------------------------------------------------------------------------
Let Crystal Reports handle the reporting - Free Crystal Reports 2008 30-Day
trial. Simplify your report design, integration and deployment - and focus on
what you do best, core application coding. Discover what's new with
Crystal Reports now. http://p.sf.net/sfu/bobj-july
_______________________________________________
ibm-acpi-devel mailing list
ibm-acpi-devel@lists.sourceforge.net
https://lists.sourceforge.net/lists/listinfo/ibm-acpi-devel
