Thanks to everyone for the replies. I carefully went thru my normal procedure everything went perfect. I like the HCD 2.5 panel which shows the HSA token like the D IOS,CONFIG command. Nice improvement.
I believe the root of my problem was, after building the new IOCDS, switching to it. Thanks again. Chip Grantham | Ameritas | Sr. IT Consultant | [email protected] 5900 O Street, Lincoln NE 68510 | p: 402-467-7382 | c: 402-429-3579 | f: 402-325-4030 "Bonaduce, Frank" <[email protected]> Sent by: IBM Mainframe Discussion List <[email protected]> 08/20/2011 01:19 AM Please respond to IBM Mainframe Discussion List <[email protected]> To [email protected] cc Subject Re: Keeping HSA, IODF, and IOCDS Hardware Tokens in SYNC Chip - Is this out-of-sync condition a pervasive problem for you ? By design, the hardware tokens are always in sync whether the configuration is loaded via CPC ACTIVATE (POR) or Dynamic Activation. The only 'out-of-sync' condition you may experience is the hardware (CSS) token and the software (OS) which isn't really a token. These should both always be in sync following a POR for every LPAR on the CPC. Following a Dynamic Activation on any given LPAR, simply perform a corresponding 'software-only' dynamic activation of the same IODF on all other LPARs on that CPC. This will put the hardware and software configurations 'back in sync'. As an aside, if you make hardware-only changes and perform a dynamic activation, all the LPARs on the CPC function under that change without a corresponding 'software activation' being performed since it effects the hardware (CSS) which is global to the CPC. If you haven't made a change to the software (OS), the software-only activation is functionally unnecessary. In any event, be certain that all LPARs on the CPC have access to the dynamically activated IODF. Frank. -----Original Message----- From: IBM Mainframe Discussion List [mailto:[email protected]] On Behalf Of Chip Grantham Sent: Friday, August 19, 2011 1:52 PM To: [email protected] Subject: Keeping HSA, IODF, and IOCDS Hardware Tokens in SYNC I seem to always run the risk of getting the hardware tokens out of sync. Can someone point me to some good reading on keeping them in sync? Thanks, Chip Grantham | Ameritas | Sr. IT Consultant | [email protected] 5900 O Street, Lincoln NE 68510 | p: 402-467-7382 | c: 402-429-3579 | f: 402-325-4030 ******* This message may contain confidential information intended only for the use of the addressee(s) named above and may contain information that is legally privileged. If you are not the addressee, or the person responsible for delivering it to the addressee, you are hereby notified that reading, disseminating, distributing or copying this message is strictly prohibited. If you have received this message by mistake, please immediately notify us by replying to the message and delete the original message immediately thereafter. Thank you. ******* ---------------------------------------------------------------------- For IBM-MAIN subscribe / signoff / archive access instructions, send email to [email protected] with the message: GET IBM-MAIN INFO Search the archives at http://bama.ua.edu/archives/ibm-main.html ---------------------------------------------------------------------- For IBM-MAIN subscribe / signoff / archive access instructions, send email to [email protected] with the message: GET IBM-MAIN INFO Search the archives at http://bama.ua.edu/archives/ibm-main.html ******* This message may contain confidential information intended only for the use of the addressee(s) named above and may contain information that is legally privileged. If you are not the addressee, or the person responsible for delivering it to the addressee, you are hereby notified that reading, disseminating, distributing or copying this message is strictly prohibited. If you have received this message by mistake, please immediately notify us by replying to the message and delete the original message immediately thereafter. Thank you. ******* ---------------------------------------------------------------------- For IBM-MAIN subscribe / signoff / archive access instructions, send email to [email protected] with the message: GET IBM-MAIN INFO Search the archives at http://bama.ua.edu/archives/ibm-main.html
