On Tue, 20 Dec 2005 09:01:14 -0600, Mark Zelden <[EMAIL PROTECTED]>
wrote:
>I can cut/paste some definitions for the
>channel attached and link attached 3745.
<snip>
I forgot to post the link attached NCP definitions. You obviously
need all the reverse PATHs to the other NCP and to VTAM host. I didn't
include the paths to the host in this (or the last) post. I'm only
including 1 of the 2 links again.
PATH DESTSA=17, ROUTES DEFINE TO NCP 17 X
ER2=(17,2,15000,15000,15000,50000), ER VIA CHAN HOST X
VR2=2, VR - ALL TRAFFIC X
VRPWS20=(1,85),VRPWS21=(1,48),VRPWS22=(1,48)
***********************************************************************
* CONFIGURABLE LINK STATION SECONDARY *
***********************************************************************
*
ST28SEC SDLCST MODE=SEC, SECONDARY STATION X
GROUP=G28SEC, GROUP FOR SECONDARY LINKS X
RETRIES=(7), RETRY 7 TIMES X
MAXOUT=127, UP TO 128 PIU'S BFOR REQUEST RESPONSX
PASSLIM=254 MAX PIU'S AT ONE TIME
*
***********************************************************************
* THE STAND-ALONE GROUP STATEMENT TO DEFINE *
* THE CHARACTERISTICS OF THE NCP IN A PRIMARY STATE *
***********************************************************************
G28PRI GROUP MODE=PRI, PRIMARY MODE X
LNCTL=SDLC, SDLC LINK PROTOCOL X
REPLYTO=1, REPLY TIMEOUT VALUE X
TEXTTO=1 TEXT TIMEOUT VALUE
***********************************************************************
* THE STAND-ALONE GROUP STATEMENT TO DEFINE *
* THE CHARACTERISTICS OF THE NCP IN A SECONDARY STATE *
***********************************************************************
G28SEC GROUP MODE=SEC, SECONDARY MODE X
LNCTL=SDLC, SDLC LINK PROCTOL X
ACTIVTO=120, SHUTDOWN TIMEOUT VALUE X
REPLYTO=NONE REPLY TIMEOUT VALUE
G28INN1 GROUP LNCTL=SDLC, SDLC LINK PROTOCOL X
ANS=CONTINUE, L-CONTINUE LINK SERVICE X
CLOCKNG=EXT, L-MODEM PROVIDES CLOCKING X
DUPLEX=FULL, L-MODEM STRAPPING IS FULL X
HISPEED=YES, L-OVER 144KPBS X
IPL=YES, L-NO CROSS-NET RPL X
MAXPU=1, L-MAX NO. OF PU ASSOCIATED WITH LINK X
MONLINK=YES, L-MONITOR LINK FOR ACTPU X
NEWSYNC=NO, L-CCU NOT PROVIDES NEWSYNC SIGNAL X
NPACOLL=YES, NPA DATA X
NRZI=NO, L-NOT-RETURN-TO-ZERO-INVERTED X
PAUSE=(0.2,0.2), L-AVERAGE POLLING CYCLE X
REPLYTO=1, REPLY TIME OUT AFTER 1 SECOND X
RETRIES=(5,15,20), L-5 RETRIES PAUSE 15 SECONDS 20 TIMESX
SDLCST=(,ST28SEC), L-SDLC SELECTION TABLE ENTRY X
SERVLIM=254, L-254 SOT SCANS BEFORE SPECIAL SCAN X
SRT=(10000,64), L-TRANS = 10000 ERROR THRESH = 64 X
SPEED=256000, L-LINE SPEED IS 256K BPS X
TRANSFR=64, L-NO. OF BUFFERS FOR SINGLE TRANSFER X
TYPE=NCP, G&L-NETWORK CONTROL MODE X
OWNER=NSP
*
L28064 LINE ADDRESS=(064,FULL), TRANSMIT AND RECEIVE ADDRESSES X
ISTATUS=ACTIVE (V) VTAM
* STATOPT='INN SA17/18 '
***********************************************************************
* PU STATEMENT FOR INN LINK TO SA 17/18 *
* (3725-V4R3) *
***********************************************************************
P28064 PU ANS=CONTINUE, CONTINUE LINK SERVICE X
MAXOUT=127, MAX PIU SENT BEFORE RESP REQ X
MODULO=128, MAX NO. OF I-FRAME SENT BEFORE RESP X
PASSLIM=254, THE MOST CONSECUTIVE PIUS SENT ONCE X
PUTYPE=4, PHYSICAL UNIT TYPE X
TGN=ANY, TRANSMISSION GROUP X
XID=YES, XID SUPPORTED X
ISTATUS=ACTIVE (V) VTAM
* STATOPT='INN SA17/18 '
Regards,
Mark
--
Mark Zelden
Sr. Software and Systems Architect - z/OS Team Lead
Zurich North America and Farmers Insurance Group
mailto: [EMAIL PROTECTED]
Systems Programming expert at http://Search390.com/ateExperts/
Mark's MVS Utilities: http://home.flash.net/~mzelden/mvsutil.html
----------------------------------------------------------------------
For IBM-MAIN subscribe / signoff / archive access instructions,
send email to [EMAIL PROTECTED] with the message: GET IBM-MAIN INFO
Search the archives at http://bama.ua.edu/archives/ibm-main.html
