As we now have an "all IBM" policy it didn't occur to me that it could be a
non-ibm message.
I have looked for the ARC1001I message with the result as below...
The whole error message (some line cutted at the end):
ARC1020I DFSMSHSM IS RECALLING FROM DASD DSN=P950OBA.A.CNTL, YOU MAY CONTINUE T
SSION BY PRESSING THE ATTENTION KEY
11/10/27 10:07:04 ECA1004E RECALL OF P950OBA.A.CNTL FAILED. RETURN CODE: 4764.
ARC1010I USER REQUEST FOR A MIGRATED DATA SET FAILED.
ARC1001I P950OBA.A.CNTL RECALL FAILED, RC=0099, REAS=4764
ARC1199I ERROR DURING RECALL/RECOVERY
***
Whats more irritating is that when looking at ARC1001I, the reasoncode is not
found in the manual.
(z/OS V1R1.0 MVS System Messages, Vol 2 (ARC-ASA) - which is where the link
from z/OS V1R13.0 DFSMShsm Diagnosis is pointing to.)
That is, they say:
2.671 ARC1001I
ARC1001I {dsname | VOL=volser | command} operation FAILED, RC=retcode
REAS=reascode
Explanation: A DFSMShsm request has failed. The following describes the message
variables:
* dsname indicates the name of the data set.
* volser indicates the volume serial number.
* command indicates the command and its associated command parameters.
* operation indicates the requested operation.
* retcode indicates the return code.
* reascode indicates the reason code.
A following related message provides you with further information about the
failure. The two digits of the message number specified as nn, indicate the
retcode. The related message number also indicates the DFSMShsm function
processing when the failure has occurred, as shown on the following table.
Table 2. Return Code Identifier
Function Message Group
Recovery/Recall ARC11nns
Space Management ARC12nns
Backup ARC13nns
Aggregate Backup/Recovery ARC6nnns
For example, if the related message is ARC1131I:
* ARC1131I indicates that the recovery/recall function has failed. The nn
is 31 which is the retcode. See Table 3 in topic 2.1266 for the meaning of
retcode 31 or refer to message ARC1131I for expanded information.
- So I look at ARC1199, where I find:
2.787 ARC1199I
ARC1199I ERROR DURING RECALL/RECOVERY
Explanation: An error was detected while DFSMShsm was performing a recall or
recovery operation. The return and reason code are given in message ARC1001I.
The possible values for the reason code are:
Reascode Meaning
4
A data set was requested to be reblocked and the accumulated record length
was greater than the DCBLRECL.
8
A direct access data set was targeted to a volume with a smaller track
capacity than the volume where the data set originally resided.
12
The DFSMShsm CDS record that describes the data set indicated a source
volume device type that is not supported by DFSMShsm.
- Non sequitur AFAICS. I the look in "ARC Return Codes and Reason Codes"
where I finally find:
" 99 VBS data set RECOVER/RECALL attempted to incompatible device."
- Which is somewhat unlikely for a JCL dataset.
- REAS=4764 is nowhere to find
Regards,
Thomas Berg
_________________________________________
Thomas Berg Specialist A M SWEDBANK
> -----Ursprungligt meddelande-----
> Från: IBM Mainframe Discussion List [mailto:[email protected]] För Lutz
> Hamann
> Skickat: den 27 oktober 2011 12:05
> Till: [email protected]
> Ämne: Re: Which manual for ECA* messages ?
>
> Thomas,
>
> looks like it is a HSM-Migrator message from EMC.
>
> ECA1004E Recall of dsn Failed. Return Code: return code
>
>
> ciao Lutz
>
> ----------------------------------------------------------------------
> For IBM-MAIN subscribe / signoff / archive access instructions,
> send email to [email protected] with the message: GET IBM-MAIN INFO
> Search the archives at http://bama.ua.edu/archives/ibm-main.html
----------------------------------------------------------------------
For IBM-MAIN subscribe / signoff / archive access instructions,
send email to [email protected] with the message: GET IBM-MAIN INFO
Search the archives at http://bama.ua.edu/archives/ibm-main.html
