Thanks Jon, I now see two new S/W problems, one mentioning that access to data has been impacted. I looked when the SAN had booted but I guess I might have been a bit too quick before that was self-diagnosed.
Oh well, reboot of the SAN it is. On Sun, Aug 2, 2020 at 7:51 PM Jon Nolting <[email protected]> wrote: > This could be the storage unit went into R/O mode to protect the existing > data. We’ve had that happen on similar old storage devices. > > See if you can check the storage HMC which might reflect the condition. We > had to “fix” whatever caused this protective condition allowing R/W access. > > Good luck > > Sent from my iPhone > > > On Aug 2, 2020, at 10:08 AM, Christian Svensson < > [email protected]> wrote: > > > > Hi, > > > > I have an old DS6800 running alongside my z114. Due to a power outage the > > SAN was shut down uncleanly and > > while it does not appear to indicate any failures in its logs or status > > displays, I'm having issues trying to IPL my LPARs from it. > > > > To try to debug this issue I loaded a z/VM installation DVD and had a > look > > at the devices. > > To reduce the number of potential error sources, I created a new CKD > volume > > at 03F1 in the DS6800. > > When I try to vary this device online I get: > > > > vary online 03f1 > > 12:59:33 HCPERP794E DASD 03F1 - ACCESS IS PROHIBITED ON VOLUME > > 12:59:33 HCPERP794E DUE TO STATUS ERROR - RC = 08 - 0004.2- 1-1112:59:33 > > HCPERP794E DASD 03F1 - ACCESS IS PROHIBITED ON VOLUME > > 12:59:33 HCPERP794E DUE TO STATUS ERROR - RC = 08 - 0004.2- 1-1112:59:33 > > HCPERP6306I DASD 03F1 AN EQUIPMENT CHECK WITH PERMANENT ERROR > > 12:59:33 HCPERP6306I OCCURRED > > 12:59:33 HCPERP6300I SENSE DATA FORMAT = 0F MSG CODE = 0C > > 12:59:33 HCPERP6301I CHANNEL COMMAND WORD COMMAND CODE = 63 > > 12:59:33 HCPERP6302I SEEK ADDRESS = 000000000000 > > 12:59:33 HCPERP6303I SENSE = 10900000 F1FFFFFC 08000000 00000004 230002CB > > 12:59:33 HCPERP6303I 0004F908 00004082 0C000000 > > 12:59:33 HCPERP6304I IRB = 01C04417 7FF0B010 02000010 00800000 > > 12:59:33 HCPERP6305I USERID = SYSTEM > > 12:59:33 HCPERP2216I CHANNEL PATH ID = F5 > > 12:59:33 HCPERP2220I PHYSICAL CHANNEL PATH ID = 011D12:59:33 HCPERP794E > > DASD 03F1 - ACCESS IS PROHIBITED ON VOLUME > > 12:59:33 HCPERP794E DUE TO STATUS ERROR - RC = 08 - 0004.2- 1-1112:59:33 > > HCPERP794E DASD 03F1 - ACCESS IS PROHIBITED ON VOLUME > > 12:59:33 HCPERP794E DUE TO STATUS ERROR - RC = 08 - 0004.2- 1-1112:59:33 > > HCPERP6306I DASD 03F1 AN EQUIPMENT CHECK WITH PERMANENT ERROR > > 12:59:33 HCPERP6306I OCCURRED > > 12:59:33 HCPERP6300I SENSE DATA FORMAT = 0F MSG CODE = 0C > > 12:59:33 HCPERP6301I CHANNEL COMMAND WORD COMMAND CODE = 27 > > 12:59:33 HCPERP6302I SEEK ADDRESS = 000000000000 > > 12:59:33 HCPERP6303I SENSE = 10900000 F1FFFFFC 08000000 00000004 230002CB > > 12:59:33 HCPERP6303I 0004F908 00004082 0C000000 > > 12:59:33 HCPERP6304I IRB = 00C04017 7FE95E50 0E000000 00800000 > > 12:59:33 HCPERP6305I USERID = SYSTEM > > 12:59:33 HCPERP2216I CHANNEL PATH ID = F5 > > 12:59:33 HCPERP2220I PHYSICAL CHANNEL PATH ID = 011D > > 12:59:33 HCPCRC8083I EREP record threshold has been exceeded for userid > > OPEREREP. Currently 00000006 records are enqueued. > > 12:59:33 HCPCPN6277I Device 03F1 cannot be varied online because I/O > errors > > occurred. > > 12:59:33 1 device(s) specified; 0 device(s) successfully varied online > > Ready(06277); T=0.01/0.01 > > > > This error is presented on the few other devices I've tried to vary > online. > > > > Any suggestions of things to try? Worst come to worst I'll power > everything > > off and do a cold boot. > > This is all a hobbyist setup so no IBM maintenance contract on anything > I'm > > afraid :-). > > > > Thanks, > > > > ---------------------------------------------------------------------- > > For IBM-MAIN subscribe / signoff / archive access instructions, > > send email to [email protected] with the message: INFO IBM-MAIN > > ---------------------------------------------------------------------- > For IBM-MAIN subscribe / signoff / archive access instructions, > send email to [email protected] with the message: INFO IBM-MAIN > ---------------------------------------------------------------------- For IBM-MAIN subscribe / signoff / archive access instructions, send email to [email protected] with the message: INFO IBM-MAIN
