After VRSEL,VERIFY do I have to activate anything?
The only change I did was adding a new VRS and ran VRSEL,VERIFY Now the previous GDG which used to get VRS pattern matched in RMM , now I don't see them Status shows MASTER and the previous one has WHILECATALG. On Wed, 22 Jul 2026, 18:59 salva, <[email protected]> wrote: > Look in SYS1.SAMPLIB(EDG*) > > El mié, 22 jul 2026, 16:22, Peter < > [email protected]> escribió: > > > I found EDGJVRSV from samplib > > > > Is the new GDG DS to be run or it can be without it for general update? > > > > On Wed, 22 Jul 2026, 18:20 rpinion865, < > > [email protected]> wrote: > > > > > The IBM DF/RMM manual???? > > > > > > > > > > > > "Confidentially doc, I am the wabbit." > > > > > > Bugs Bunny > > > > > > Sent with Proton Mail secure email. > > > > > > On Wednesday, July 22nd, 2026 at 10:18 AM, Peter < > > > [email protected]> wrote: > > > > > > > Where can I find the sample JCL to run EDGHSKP with > PARM='VRSEL,VERIFY > > ' > > > ? > > > > > > > > On Wed, 22 Jul 2026, 15:09 Peter, <[email protected]> wrote: > > > > > > > > > Ok got it > > > > > > > > > > So EDGHSKP scans and sets it and newly added VRS are not in > immediate > > > > > effect. Instead it waits till the HSKP finishes its task > > > > > > > > > > On Wed, 22 Jul 2026, 14:56 salva, <[email protected]> wrote: > > > > > > > > > >> VRS are assigned in the daily maintenance job. Check the output! > > > > >> > > > > >> El mié, 22 jul 2026 a las 12:28, Peter (< > > > > >> [email protected]>) escribió: > > > > >> > > > > >> > Hello Salva > > > > >> > > > > > >> > I added the new VRS > > > > >> > > > > > >> > BACKUP.Z%%%%%.WEEKLY.G^^^^V^^ > > > > >> > > > > > >> > So when I took a volume level of backup for Z31SMP. It created > the > > > GDG > > > > >> > > > > > >> > BACKUP.Z31SMP.WEEKLY.G0004V01 but the VRS I created didn't match > > it. > > > > >> > > > > > >> > Am i missing something? > > > > >> > > > > > >> > On Wed, 22 Jul 2026, 13:39 salva, <[email protected]> wrote: > > > > >> > > > > > >> > > Usually it's defined in a VRS rule. > > > > >> > > Check RMM SEARCHVRS, ISPF user interface to RMM or ask your > > > stgadmin > > > > >> if > > > > >> > > you are not auth. > > > > >> > > > > > > >> > > > > > > >> > > > > > > >> > > El mié, 22 jul 2026 a las 10:51, Peter (< > > > > >> > > [email protected]>) escribió: > > > > >> > > > > > > >> > > > Hello > > > > >> > > > > > > > >> > > > I am trying to take backup of volume on virtual tape. > > > Automatically > > > > >> its > > > > >> > > > retention period is set for 6 days. I have not specified the > > > RETPD > > > > >> in > > > > >> > > > ADRDSSU JCL. > > > > >> > > > > > > > >> > > > Even the management class has no expiry set for these GDG > > > created on > > > > >> > > tape. > > > > >> > > > > > > > >> > > > Not sure from where these expiry are set Automatically. > > > > >> > > > > > > > >> > > > Could you please point me in the right direction > > > > >> > > > > > > > >> > > > Regards > > > > >> > > > Peter > > > > >> > > > > > > > >> > > > > > > > >> > > ---------------------------------------------------------------------- > > > > >> > > > For IBM-MAIN subscribe / signoff / archive access > > instructions, > > > > >> > > > send email to [email protected] with the message: > INFO > > > > >> IBM-MAIN > > > > >> > > > > > > > >> > > > > > > >> > > > > > ---------------------------------------------------------------------- > > > > >> > > For IBM-MAIN subscribe / signoff / archive access > instructions, > > > > >> > > send email to [email protected] with the message: INFO > > > > >> IBM-MAIN > > > > >> > > > > > > >> > > > > > >> > > > > ---------------------------------------------------------------------- > > > > >> > For IBM-MAIN subscribe / signoff / archive access instructions, > > > > >> > send email to [email protected] with the message: INFO > > > IBM-MAIN > > > > >> > > > > > >> > > > > >> > > ---------------------------------------------------------------------- > > > > >> For IBM-MAIN subscribe / signoff / archive access instructions, > > > > >> send email to [email protected] with the message: INFO > > > IBM-MAIN > > > > >> > > > > > > > > > > > > > > ---------------------------------------------------------------------- > > > > For IBM-MAIN subscribe / signoff / archive access instructions, > > > > send email to [email protected] with the message: INFO > IBM-MAIN > > > > > > > > > > ---------------------------------------------------------------------- > > > For IBM-MAIN subscribe / signoff / archive access instructions, > > > send email to [email protected] with the message: INFO IBM-MAIN > > > > > > > ---------------------------------------------------------------------- > > For IBM-MAIN subscribe / signoff / archive access instructions, > > send email to [email protected] with the message: INFO IBM-MAIN > > > > ---------------------------------------------------------------------- > For IBM-MAIN subscribe / signoff / archive access instructions, > send email to [email protected] with the message: INFO IBM-MAIN > ---------------------------------------------------------------------- For IBM-MAIN subscribe / signoff / archive access instructions, send email to [email protected] with the message: INFO IBM-MAIN
